- 您現在的位置：買賣IC網 > PDF目錄19382 > ADSP-2188NKSTZ-320 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-2188NKSTZ-320 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 100LQFP |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 主機接口，串行端口 |
| 時鐘速率： | 80MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 256kB |
| 電壓 - 輸入/輸出： | 1.8V，2.5V，3.3V |
| 電壓 - 核心： | 1.80V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADSP-218xN
Rev. A
|
Page 25 of 48
|
August 2006
ENVIRONMENTAL CONDITIONS
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured out-
put high or low voltage to a high impedance state. The output
disable time (tDIS) is the difference of tMEASURED and tDECAY, as
shown in Figure 20. The time is the interval from when a refer-
ence signal reaches a high or low voltage level to when the
output voltages have changed by 0.5 V from the measured out-
put high or low voltage.
The decay time, tDECAY, is dependent on the capacitive load, CL,
and the current load, iL, on the output pin. It can be approxi-
mated by the following equation:
from which
is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.
Output Enable Time
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in Figure 20. If multiple pins (such as the data bus) are enabled,
the measurement value is that of the first pin to start driving.
Table 14. Thermal Resistance
Rating Description
1
1 Where the Ambient Temperature Rating (TAMB) is:
TAMB = TCASE – (PD × θCA)
TCASE = Case Temperature in °C
PD = Power Dissipation in W
Symbol
LQFP
(
°C/W)
BGA
(
°C/W)
Thermal Resistance (Case-
to-Ambient)
θ
CA
48
63.3
Thermal Resistance
(Junction-to-Ambient)
θ
JA
50
70.7
Thermal Resistance
(Junction-to-Case)
θ
JC
27.4
Figure 18. Voltage Reference Levels for AC Measurements (Except Output
Enable/Disable)
Figure 19. Equivalent Loading for AC Measurements (Including All Fixtures)
1.5V
OUTPUT
INPUT
1.5V
2.0V
0.8V
TO
OUTPUT
PIN
50pF
1.5V
I
OH
IOL
Figure 20. Output Enable/Disable
2.0V
1.0V
tENA
REFERENCE
SIGNAL
OUTPUT
tDECAY
VOH
(MEASURED)
OUTPUT STOPS
DRIVING
OUTPUT STARTS
DRIVING
tDIS
tMEASURED
VOL
(MEASURED)
VOH (MEASURED) – 0.5V
VOL (MEASURED) + 0.5V
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
VOH
(MEASURED)
VOL
(MEASURED)
tDECAY
CL 0.5V
×
iL
------------------------
=
tDIS
tMEASURED tDECAY
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WF-CY-F3 | CONVERTER MOD DC/DC 72V 50W |
| RCM08DTBD-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| VI-2WB-CY-F1 | CONVERTER MOD DC/DC 95V 50W |
| MIC3232YMM | IC LED DRVR HP CONS CURR 10-MSOP |
| 1130-561K-RC | CHOKE RF HI CURR 560UH 10% RAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2188NKSTZ-3202 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2188N-WFA | 制造商:Analog Devices 功能描述: |
| ADSP-2189 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2189M | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2189M_99 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。