- 您現在的位置：買賣IC網 > PDF目錄364643 > ADS931E Analog-to-Digital Converter, 8-Bit PDF資料下載
參數資料
| 型號： | ADS931E |
| 元件分類： | ADC |
| 英文描述： | Analog-to-Digital Converter, 8-Bit |
| 中文描述： | 8位模數轉換器 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 247K |
| 代理商： | ADS931E |
ADS931
SBAS060A
9
R
1
1k
OPA680
V
IN
R
F
402
V
CM
C
0.1μF
0.1μF
IN
CM
+5V
R
S
50
+5V
R
G
402
C
0.1μF
22pF
ADS931
R
P(1)
402
NOTE: (1) See text for discussion.
The pipelined quantizer architecture has 7 stages with each
stage containing a two-bit quantizer and a two bit digital-
to-analog converter, as shown in Figure 2. Each two-bit
quantizer stage converts on the edge of the sub-clock, which
is the same frequency of the externally applied clock. The
output of each quantizer is fed into its own delay line to
time-align it with the data created from the subsequent
quantizer stages. This aligned data is fed into a digital error
correction circuit which can adjust the output data based on
the information found on the redundant bits. This technique
provides the ADS931 with excellent differential linearity
and guarantees no missing codes at the 8-bit level.
To accommodate a bipolar signal swing, the ADS931 oper-
ates with a common-mode voltage (V
CM
) which is derived
from the external references. Due to the symmetric resistor
ladder inside the ADS931, V
CM
is situated between the top
and bottom reference voltage. Equation 1 can be used for
calculating the common-mode voltage level.
V
CM
= (REFT +REFB)/2
(1)
At the same time, the two external reference voltage levels
define the full-scale input range for the ADS931. This makes
it possible for the input range to be adapted to the signal
swing of the front end.
APPLICATIONS
SIGNAL SWING AND COMMON-MODE
CONSIDERATIONS
The ADS931 is primarily designed and specified for a +3V
single supply voltage. However, due to its supply range of
+2.7V to +5.25V, it is well suited for +5V applications. The
nominal input signal swing is 1Vp-p, situated between +1V
and +2V. This means that the signal swings
±
0.5V around a
common-mode voltage of +1.5V when using a 3V rail, or
typically +2.75V on a 5V supply. In some applications, it
might be advantageous to increase the input signal swing.
For example, increasing it to 2Vp-p may improve the achiev-
able signal-to-noise performance. However, consideration
should be given to keeping the signal swing within the linear
range of operation of the driving circuitry to avoid any
excessive distortion. In extreme situations, the performance
of the converter will start to degrade due to large variations
of the input’s switch ON resistance over the input voltage.
Therefore, the signal swing should remain approximately
0.5V away from each rail during normal operation.
DRIVING THE ANALOG INPUTS
AC-COUPLED DRIVER
Figure 3 shows an example of an ac-coupled, single-ended
interface circuit using a high speed op amp which operates
on dual supplies (OPA650, OPA658). The mid-point refer-
ence voltage, (V
CM
), biases the bipolar, ground-referenced
input signal. The capacitor C
1
and resistor R
1
form a high-
pass filter with the –3dB frequency set at
f
–3dB
= 1/(2
π
R
1
C
1
)
(2)
The values for C
1
and R
1
are not critical in most applications
and can be set freely. The values shown in Figure 3 corre-
spond to a corner frequency of 1.6kHz.
FIGURE 4. +5V Single-Supply Interface Circuit Example Using the Voltage Feedback Amplifier OPA680.
Figure 4 depicts a circuit that can be used in single-supply
applications. The mid-reference voltage biases the op amp
up to the appropriate common-mode voltage, for example
V
CM
= +1.5V. With the use of capacitor C
G
, the DC gain for
the non-inverting op amp input is set to +1V/V. As a result,
the transfer function is modified to
V
OUT
= V
IN
{(1 + R
F
/R
G
) + V
CM
}
(3)
FIGURE 3. AC-Coupled, Single-Ended Interface Circuit.
402
OPA65x
V
IN
402
R
1
1k
V
CM
C
0.1μF
0.1μF
IN
CM
+5V
R
S
50
–
5V
+V
S
ADS931
相關PDF資料 |
PDF描述 |
|---|---|
| ADSST-21065LKS-240 | High End, Multichannel, 32-Bit Floating-Point Audio Processor |
| ADSST-21065LKS-264 | High End, Multichannel, 32-Bit Floating-Point Audio Processor |
| ADSST-21065LCS-240 | High End, Multichannel, 32-Bit Floating-Point Audio Processor |
| ADSST-21065LKCA-240 | High End, Multichannel, 32-Bit Floating-Point Audio Processor |
| ADSST-21065LKCA-264 | High End, Multichannel, 32-Bit Floating-Point Audio Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS931E | 制造商:Texas Instruments 功能描述:IC 8BIT ADC 30MSPS 28SSOP 制造商:Texas Instruments 功能描述:IC, 8BIT ADC, 30MSPS, 28SSOP 制造商:Texas Instruments 功能描述:IC, 8BIT ADC, 30MSPS, 28SSOP; Resolution (Bits):8bit; Sampling Rate:33MSPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:23mA; Digital IC Case Style:SSOP; No. of Pins:28; Input Channel ;RoHS Compliant: Yes |
| ADS931E/1K | 功能描述:模數轉換器 - ADC 8-Bit 30 MSPS SE/ Diff Input RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS931E/1KG4 | 功能描述:模數轉換器 - ADC 8-Bit 30 MSPS SE/ Diff Input RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS931EG4 | 功能描述:模數轉換器 - ADC 8-Bit 30 MSPS SE/ Diff Input RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS-931MC | 制造商:Murata Power Solutions 功能描述:ADC Single 2-Step Flash 1Msps 16-bit Parallel 40-Pin TDIP |
發布緊急采購，3分鐘左右您將得到回復。