
www.ti.com
ELECTRICAL CHARACTERISTICS
At T
A
= -40°C to 85°C, f
s
= 250 kHz, V
DIG
= V
ANA
= 5 V, using internal reference and 0.1%, 0.25 W fixed resistors (See
Figure 29
and
Figure 30
) (unless otherwise specified)
ADS8509
SLAS324A–OCTOBER 2004–REVISED JUNE 2005
ADS8509I
ADS8509IB
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
MIN
TYP
MAX
Resolution
16
16
Bits
ANALOG INPUT
Voltage ranges
(1)
Impedance
(1)
Capacitance
50
50
pF
THROUGHPUT SPEED
Conversion cycle
Acquire and convert
4
4
μs
Throughput rate
250
250
kHz
DC ACCURACY
INL
Integral linearity error
-3
3
-2
2
LSB
(2)
DNL
Differential linearity error
-2
2
-1
1
LSB
No missing codes
15
16
Bits
Transition noise
(3)
1
1
LSB
±10 V range
Int. Ref. with 0.1% external
fixed resistors
-0.5
0.5
-0.5
0.5
Full-scale
error
(4)(5)
%FSR
All other ranges
-0.5
0.5
-0.5
0.5
Full-scale error drift
Int. Ref.
±7
±7
ppm/°C
±10 V range
Ext. Ref. with 0.1% external
fixed resistors
-0.5
0.5
-0.5
0.5
Full-scale
error
(4)(5)
%FSR
All other ranges
-0.5
0.5
-0.5
0.5
Full-scale error drift
Ext. Ref.
±2
±2
ppm/°C
Bipolar zero error
(4)
-10
10
-5
5
mV
Bipolar zero error drift
±0.4
±0.4
ppm/°C
10 V range
-5
5
-5
5
Unipolar zero
error
(4)
mV
4 V and 5 V
range
-3
3
-3
3
Unipolar zero error drift
±2
±2
ppm/°C
Recovery to rated accuracy after
power down
1-μF Capacitor to CAP
1
1
ms
Power supply sensitivity
(V
DIG
= V
ANA
= V
D
)
AC ACCURACY
-8
8
-8
8
+4.75 V < V
D
< +5.25 V
LSB
SFDR
Spurious-free dynamic range
f
I
= 20 kHz
f
I
= 20 kHz
f
I
= 20 kHz
–60-dB Input
90
99
95
99
dB
(6)
THD
Total harmonic distortion
-98
-90
-98
-93
dB
SINAD
83
88
85
88
dB
Signal-to-(noise+distortion)
30
32
dB
SNR
Signal-to-noise ratio
f
I
= 20 kHz
83
88
86
88
dB
Full-power bandwidth
(7)
500
500
kHz
SAMPLING DYNAMICS
Aperture delay
5
5
ns
Transient response
FS Step
2
2
μs
Overvoltage recovery
(8)
150
150
ns
(1)
(2)
(3)
(4)
±10 V, 0 V to 5 V, etc. (see
Table 3
)
LSB means least significant bit. For the ±10-V input range, one LSB is 305 μV.
Typical rms noise at worst case transitions and temperatures.
As measured with fixed resistors shown in
Figure 29
and
Figure 30
. Adjustable to zero with external potentiometer. Factory calibrated
with 0.1%, 0.25 W resistors.
For bipolar input ranges, full-scale error is the worst case of -full-scale or +full-scale uncalibrated deviation from ideal first and last code
transitions, divided by the transition voltage (not divided by the full-scale range) and includes the effect of offset error. For unipolar input
ranges, full-scale error is the deviation of the last code transition divided by the transition voltage. It also includes the effect of offset
error.
All specifications in dB are referred to a full-scale ±10-V input.
Full-power bandwidth is defined as the full-scale input frequency at which signal-to-(noise + distortion) degrades to 60 dB.
Recovers to specified performance after 2 x FS input overvoltage.
(5)
(6)
(7)
(8)
3