- 您現在的位置：買賣IC網 > PDF目錄223311 > ADS8382IBRHPT (TEXAS INSTRUMENTS INC) 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC28 PDF資料下載
參數資料
| 型號： | ADS8382IBRHPT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC28 |
| 封裝： | 6 X 6 MM, GREEN, PLASTIC, QFN-28 |
| 文件頁數： | 18/35頁 |
| 文件大小： | 1416K |
| 代理商： | ADS8382IBRHPT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
NAP MODE
Full ICC
SDO
BUSY
LSB
SAMPLE
NAP
CONVERT
SAMPLE
LSB+1
MSB
MSB1
HiZ
tCONV
td16
td18
ICC NAP
Full ICC
PD = 0
CONVST
CS
CONVST_QUAL
DEVICE
STATE
REFIN
(or REFOUT)
ICC
LAYOUT
ADS8382
SLAS416B – JUNE 2004 – REVISED NOVEMBER 2004
Nap mode is automatically inserted at the end of a conversion if CONVST_QUAL is held low at EOC. The device
can be operated in nap mode at the end of every conversion for saving power at lower throughputs. Another way
to use this mode is to convert multiple times and then enter nap mode. The minimum sampling time after a nap
state is tacq1 + td18 = tacq2.
Figure 57. Device Nap Power Down/Resume
For optimum performance, care should be taken with the physical layout of the ADS8382 circuitry.
Since the ADS8382 offers single-supply operation, it is often used in close proximity with digital logic,
microcontrollers, microprocessors, and digital signal processors. The more the digital logic in the design and the
higher the switching speed, the greater the need for better layout and isolation of the critical analog signals from
these switching digital signals.
The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground
connections and digital inputs that occur just prior to the end of sampling and just prior to the latching of the
analog comparator. Such glitches might originate from switching power supplies, nearby digital logic, or high
power devices. Noise during the end of sampling and the latter half of the conversion must be kept to a minimum
(the former half of the conversion is not very sensitive since the device uses a proprietary error correction
algorithm to correct for the transient errors made here).
The degree of error in the digital output depends on the reference voltage, layout, and the exact timing and
degree of the external event.
On average, the ADS8382 draws very little current from an external reference as the reference voltage is
internally buffered. If the reference voltage is external, it must be ensured that the reference source can drive the
bypass capacitor without oscillation. A 0.1-
F bypass capacitor is recommended from pin 8 directly to pin 7
(REFM).
The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the
analog ground. Avoid connections that are too close to the grounding point of a microcontroller or digital signal
processor. If required, run a ground trace directly from the converter to the power supply entry point. The ideal
layout consists of an analog ground plane dedicated to the converter and associated analog circuitry.
25
相關PDF資料 |
PDF描述 |
|---|---|
| ADS8422IBPFBR | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| ADSP-2189NBSTZ-320 | 16-Bit, 80MIPS, 1.8V, 2 Serial Ports, Host Port, 192KB RAM; Package: 100 ld LQFP; No of Pins: 100; Temperature Range: Ind |
| ADSP-2189NKCAZ-320 | 16-Bit, 80MIPS, 1.8V, 2 Serial Ports, Host Port, 192KB RAM; Package: CHIP SCALE BGA; No of Pins: 144; Temperature Range: Comm. |
| ADSP-2189NKSTZ-320 | 16-Bit, 80MIPS, 1.8V, 2 Serial Ports, Host Port, 192KB RAM; Package: 100 ld LQFP; No of Pins: 100; Temperature Range: Comm. |
| ADSP-2191MBCAZ-140 | 16-bit Fixed-Point DSP, 160 MIPS, 160K bytes RAM; Package: CHIP SCALE BGA; No of Pins: 144; Temperature Range: Ind |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8382IBRHPTG4 | 功能描述:模數轉換器 - ADC 18-Bit 600KSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8382IRHPR | 功能描述:模數轉換器 - ADC 18-Bit 600KSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8382IRHPRG4 | 功能描述:模數轉換器 - ADC 18-Bit 600KSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8382IRHPT | 功能描述:模數轉換器 - ADC 18-Bit 600KSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8382IRHPTG4 | 功能描述:模數轉換器 - ADC 18-Bit 600KSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。