- 您現在的位置：買賣IC網 > PDF目錄375266 > ADS831E MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:25V; Continuous Drain Current, Id:0.75A; On-Resistance, Rds(on):0.35ohm; Rds(on) Test Voltage, Vgs:4.5V; Package/Case:3-SC-70; Leaded Process Compatible:No PDF資料下載
參數資料
| 型號： | ADS831E |
| 英文描述： | MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:25V; Continuous Drain Current, Id:0.75A; On-Resistance, Rds(on):0.35ohm; Rds(on) Test Voltage, Vgs:4.5V; Package/Case:3-SC-70; Leaded Process Compatible:No |
| 中文描述： | 8位，80MHz的采樣模擬數字轉換器 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 179K |
| 代理商： | ADS831E |
7
ADS831
APPLICATION INFORMATION
THEORY OF OPERATION
The ADS831 is a high-speed CMOS analog-to-digital con-
verter which employs a pipelined converter architecture
consisting of 6 internal stages. Each stage feeds its data into
the digital error correction logic ensuring excellent differen-
tial linearity and no missing codes at the 8-bit level. The
output data becomes valid on the rising clock edge (see
Timing Diagram). The pipeline architecture results in a data
latency of 4 clock cycles.
The analog input of the ADS831 is a differential track and
hold, see Figure 1. The differential topology along with
tightly matched capacitors produce a high level of ac perfor-
mance while sampling at very high rates.
The ADS831 allows its analog inputs to be driven either
single-ended or differentially. The typical configuration for
the ADS831 is for the single-ended mode in which the input
track and hold performs a single-ended to differential con-
version of the analog input signal.
Both inputs (IN, IN) require external biasing using a com-
mon-mode voltage that is typically at the mid-supply level
(+V
S
/2).
The following application discussion focuses on the single-
ended configuration. Typically, its implementation is easier
to achieve and the rated specifications for the ADS831 are
characterized using the single-ended mode of operation.
DRIVING THE ANALOG INPUT
The ADS831 achieves excellent ac performance either in the
single-ended or differential mode of operation. The selection
for the optimum interface configuration will depend on the
individual application requirements and system structure.
For example, communication applications often process a
band of frequencies that does not include DC, whereas in
imaging applications, the previously restored DC level must
be maintained correctly up to the A/D converter. Features on
the ADS831, such as the input range select (RSEL pin) or
the option for an external reference, provide the needed
flexibility to accommodate a wide range of applications. In
any case, the ADS831 should be configured such that the
application objectives are met while observing the headroom
requirements of the driving amplifier in order to yield the
best overall performance.
INPUT CONFIGURATIONS
AC-Coupled, Single-Supply Interface
Figure 2 shows the typical circuit for an ac-coupled analog
input configuration of the ADS831 where all components
are powered from a single +5V supply.
With the RSEL pin connected HIGH, the full scale input
range is set to 2Vp-p. In this configuration, the top and
bottom references (REFT, REFB) provide an output voltage
of +3.0V and +2.0V, respectively. Two resistors ( 2 x 1k
)
are used to create a common-mode voltage (V
CM
) of ap-
proximately +2.5V to bias the inputs of the driving ampli-
fier. Using the OPA681 on a single +5V supply, its ideal
common-mode point is +2.5V. This coincides with the
recommended common-mode input level for the ADS831
thus, obviating the need for a coupling capacitor between the
amplifier and the converter. Even though the OPA681 has an
ac gain of +2, the dc gain is only +1 due to the blocking
capacitor at resistor R
G
.
The addition of a small series resistor (R
S
) between the
output of the op amp and the input of the ADS831 will be
beneficial in almost all interface configurations. This will
de-couple the op amp’s output from the capacitive load and
avoid gain peaking, which can result in increased noise. For
best spurious and distortion performance, the resistor value
should be kept below 75
. The series resistor in combina-
tion with the 47pF capacitor establishes a passive low-pass
filter limiting the bandwidth for the wideband noise thus
help improving the SNR performance.
AC-Coupled, Dual Supply Interface
The circuit provided in Figure 3 shows typical connections
for the analog input in case the selected amplifier operates
on dual supplies. This might be necessary to take full
advantage of very low distortion operational amplifiers, like
the OPA642. The advantage is that the driving amplifier can
be operated with a ground referenced bipolar signal swing.
This will keep the distortion performance at its lowest since
the signal range stays within the linear region of the op amp
and sufficient headroom to the supply rails can be main-
tained. By capacitively coupling the single-ended signal to
the input of the ADS831, its common-mode requirements
can easily be satisfied with two resistors connected between
the top and bottom reference.
FIGURE 1. Simplified Circuit of Input Track and Hold with
Timing Diagram.
φ
1
φ
1
φ
2
φ
1
φ
1
φ
1
φ
1
φ
1
φ
2
φ
1
φ
2
φ
1
φ
2
IN
IN
OUT
OUT
Op Amp
Bias
V
CM
Op Amp
Bias
V
CM
C
H
C
I
C
I
C
H
Input Clock (50%)
Internal Non-overlapping Clock
相關PDF資料 |
PDF描述 |
|---|---|
| ADS8320 | 16-Bit, High-Speed, 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS8320E | 16-Bit, High-Speed, 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS8320EB | 16-Bit, High-Speed, 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS8323 | TERMINAL |
| ADS8343 | 16-Bit, 4-Channel Serial Output Sampling ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS831E/1K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog to Digital Converter |
| ADS831E/2K5 | 功能描述:模數轉換器 - ADC 8-Bit 80 MSPS SE/Diff Inputs RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS831E/2K5G4 | 功能描述:模數轉換器 - ADC 8-Bit 80 MSPS SE/Diff Inputs RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS831EG4 | 功能描述:模數轉換器 - ADC 8-Bit 80 MSPS SE/Diff Inputs RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8320 | 制造商:BB 制造商全稱:BB 功能描述:16-Bit, High-Speed, 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。