- 您現在的位置：買賣IC網 > PDF目錄10372 > ADS7825PG4 (Texas Instruments)IC MUX 16-BIT 4CH A/D 28-DIP PDF資料下載
參數資料
| 型號： | ADS7825PG4 |
| 廠商： | Texas Instruments |
| 文件頁數： | 6/21頁 |
| 文件大小： | 0K |
| 描述： | IC MUX 16-BIT 4CH A/D 28-DIP |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 13 |
| 位數： | 16 |
| 采樣率（每秒）： | 40k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 50mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 28-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，雙極 |
14
ADS7825
conversions will proceed through each higher channel, cy-
cling back to zero after Channel 3.
If PWRD is held HIGH for a significant period of time, the
REF (pin 7) bypass capacitor may discharge (if the internal
reference is being utilized) and the CAP (pin 6) bypass
capacitor will discharge (for both internal and external
references). The continuous conversion mode should not be
enabled until the bypass capacitor(s) have recharged and
stabilized (1ms for 2.2
F capacitors recommended). In
addition, the continuous conversion mode should not be
enabled even with a short pulse on PWRD until the mini-
mum acquisition time has been met.
MANUAL CHANNEL SELECTION (CONTC= 0V)
The channels of the ADS7825 can be selected manually by
using the A0 and A1 address pins (pins 19 and 18, respec-
tively). See Table IVb for the multiplexer truth table and
Figure 8 for channel selection timing.
into the A0 and A1 registers (pins 19 and 18, respectively)
prior to CONTC being raised HIGH, becomes the first
address in the sequential continuous conversion mode (e.g.,
if Channel 1 was the last address selected then Channel 2
will follow, then Channel 3, and so on). The A0 and A1
address inputs become outputs when the device is in this
mode. When BUSY rises at the end of a conversion, A0 and
A1 will output the address of the channel that will be
converted when BUSY goes LOW at the beginning of the
next conversion. Data will be valid for the previous channel
when BUSY rises. See Table IVa and Figure 7 for channel
selection timing in continuous conversion mode.
PWRD (pin 26) can be used to reset the multiplexer address
to zero. With the ADS7825 configured for no conversion,
PWRD can be taken HIGH for a minimum of 200ns. When
PWRD returns LOW, the multiplexer address will be reset
to zero. When the continuous conversion mode is enabled,
the first conversion will be done on channel 0. Subsequent
ADS7825 TIMING AND CONTROL
FIGURE 7. Channel Addressing in Continuous Conversion Mode (CONTC HIGH, CS and R/C LOW).
FIGURE 8. Channel Addressing in Normal Conversion Mode (CONTC and CS LOW).
0
AIN3
AIN0
0
1
AIN0
AIN1
1
0
AIN1
AIN2
1
AIN2
AIN3
DATA AVAILABLE
CHANNEL TO BE OR
A1
A0
FROM CHANNEL
BEING CONVERTED
DESCRIPTION OF OPERATION
Channel being acquired or converted is output on these
address lines. Data is valid for the previous channel. These
lines are updated when BUSY rises.
TABLE IVa. A0 and A1 Outputs (CONTC HIGH).
CHANNEL SELECTED
A1
A0
WHEN BUSY GOES HIGH
DESCRIPTION OF OPERATION
0
AIN0
0
1
AIN1
1
0
AIN2
1
AIN3
TABLE IVb. A0 and A1 Inputs (CONTC LOW).
Channel to be converted during conversion 'n + 1' is latched
when conversion 'n' is initiated (BUSY goes LOW). The selected
input starts being acquired as soon as conversion 'n' is done
(BUSY goes HIGH).
R/C
BUSY
A0, A1
(Input)
D7-D0
n – 3
n – 2
n – 1
n
n + 1
n + 2
n + 3
n – 1
n
n + 1
n + 2
n + 3
n + 4
n + 5
n + 4
n + 3
n + 2
n + 1
n
n – 1
n – 2
n + 4
Conversion Currently in Progress:
Channel Address for Conversion:
Results from Conversion:
t
30
BUSY
A0, A1
(Output)
D7-D0
n – 3
n – 2
n – 1
n
n + 1
n + 2
n + 3
n – 2
n – 1
n
n + 1
n + 2
n + 3
n + 4
n + 3
n + 2
n + 1
n
n – 1
n – 2
n + 5
n + 4
Conversion Currently in Progress:
Channel Address for Conversion:
Results from Conversion:
t
29
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484T12F8A | CONN HSG PLUG 8POS STRAIGHT PIN |
| D38999/20WC8SNLC | CONN HSG RCPT 8POS WALL MT SCKT |
| MS27467T13B4PLC | CONN HSG PLUG 4POS STRGHT PINS |
| MS27484T16B26BA | CONN HSG PLUG 26POS STRGHT SCKT |
| MS27508E22B35A | CONN HSG RCPT 100POS BOX MT PIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7825U | 功能描述:模數轉換器 - ADC 4 Channel 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7825U | 制造商:BURR-BROWN 功能描述:16BIT ADC 4CH SMD 7825 SOIC28 |
| ADS7825U/1K | 功能描述:模數轉換器 - ADC 4 Channel 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7825U/1KE4 | 功能描述:模數轉換器 - ADC 4 Channel 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7825UB | 功能描述:模數轉換器 - ADC 4 Channel 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。