- 您現在的位置：買賣IC網 > PDF目錄364640 > ADS7811 16-Bit 250kHz Sampling CMOS ANALOG-to-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS7811 |
| 英文描述： | 16-Bit 250kHz Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| 中文描述： | 16位至250kHz采樣CMOS模擬數字轉換器 |
| 文件頁數： | 9/9頁 |
| 文件大?。?/td> | 186K |
| 代理商： | ADS7811 |
ADS7811
9
the 74HC574s but should be kept at least 1/4" (6mm) distant
from the digital ground plane (if present). The analog and
digital grounds planes should not overlap at any point.
INTERMEDIATE LATCHES
The 74HC574s shown in Figure 1 isolate the ADS7811 from
digital signals on a microprocessor, digital signal processor
(DSP), or microcontroller bus. This is necessary because of
the precision needed within the ADS7811. The weight of a
single LSB in the ADS7811 is 76
μ
V, and the comparator
must be able to resolve differences in voltage to this level.
External digital signals which transition during the conver-
sion can easily couple onto the substrate and produce volt-
ages larger than this.
In place of the 74HC574s, it might be possible to use a FIFO
or similar type of memory device. For many systems, it may
be difficult to go directly from the ADS7811 into a
microcontroller or DSP even if the ADS7811 is not con-
nected to shared bus. The reason for this is that the outputs
are active only during the acquisition period.
SIGNAL CONDITIONING
The ADS7811 input essentially consists of a switch and a
capacitor. In the acquisition or sample mode, the switch is
closed and the input signal drives the capacitor directly.
When a conversion is started, the switch is opened capturing
the input signal at that moment. This voltage is held on the
capacitor for the remainder of the conversion.
While this provides for a wide bandwidth sample and hold
function and results in excellent AC performance, this archi-
tecture requires a high bandwidth, precision op amp to drive
the analog input. The op amp and configuration shown in
Figure 1 is highly recommended. The amplifier should be
placed within 1 to 2 inches (25 to 50mm) of the ADS7811,
and the layout guidelines in the OPA628 data sheet should
be strictly followed.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS7811U | CMOS Quad 2-Input NOR Gate 14-PDIP -55 to 125 |
| ADS7812 | Low-Power, Serial 12-Bit Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7812P | Low-Power, Serial 12-Bit Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7812PB | Low-Power, Serial 12-Bit Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7812U | Low-Power, Serial 12-Bit Sampling ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7811U | 功能描述:模數轉換器 - ADC 16-Bit 250kHz Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7811U | 制造商:Texas Instruments 功能描述:Analog-Digital Converter IC Number of Bi |
| ADS7811U/1K | 功能描述:模數轉換器 - ADC 16-Bit 250kHz Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7811U/1KE4 | 功能描述:模數轉換器 - ADC 16-Bit 250kHz Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7811U/1KG4 | 功能描述:模數轉換器 - ADC 16-Bit 250kHz Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。