- 您現在的位置：買賣IC網 > PDF目錄223311 > ADS7806PB (TEXAS INSTRUMENTS INC) 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PDIP28 PDF資料下載
參數資料
| 型號： | ADS7806PB |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, PDIP28 |
| 封裝： | 0.300 INCH, GREEN, PLASTIC, DIP-28 |
| 文件頁數： | 23/25頁 |
| 文件大小： | 670K |
| 代理商： | ADS7806PB |
ADS7806
7
SBAS021B
www.ti.com
BASIC OPERATION
PARALLEL OUTPUT
Figure 1a shows a basic circuit to operate the ADS7806 with
a
±10V input range and parallel output. Taking R/C (pin 22)
LOW for 40ns (12
s max) will initiate a conversion. BUSY
(pin 24) will go LOW and stay LOW until the conversion is
completed and the output register is updated. If BYTE (pin
21) is LOW, the eight Most Significant Bits (MSBs) will be
valid when BUSY rises; if BYTE is HIGH, the four Least
Significant Bits (LSBs) will be valid when BUSY rises. Data
will be output in Binary Two’s Complement (BTC) format.
BUSY going HIGH can be used to latch the data. After the
first byte has been read, BYTE can be toggled allowing the
remaining byte to be read. All convert commands will be
ignored while BUSY is LOW.
The ADS7806 will begin tracking the input signal at the end
of the conversion. Allowing 25
s between convert com-
mands assures accurate acquisition of a new signal.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compen-
sate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
SERIAL OUTPUT
Figure 1b shows a basic circuit to operate the ADS7806 with
a
±10V input range and serial output. Taking R/C (pin 22)
LOW for 40ns (12
s max) will initiate a conversion and
output valid data from the previous conversion on SDATA
(pin 19) synchronized to 12 clock pulses output on DATACLK
(pin 18). BUSY (pin 24) will go LOW and stay LOW until the
conversion is completed and the serial data has been trans-
mitted. Data will be output in BTC format, MSB first, and will
be valid on both the rising and falling edges of the data clock.
BUSY going HIGH can be used to latch the data. All convert
commands will be ignored while BUSY is LOW.
The ADS7806 will begin tracking the input signal at the end
of the conversion. Allowing 25
s between convert com-
mands assures accurate acquisition of a new signal.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compen-
sate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
STARTING A CONVERSION
The combination of CS (pin 23) and R/C (pin 22) LOW for a
minimum of 40ns immediately puts the sample-and-hold of
the ADS7806 in the hold state and starts conversion ‘n’.
BUSY (pin 24) will go LOW and stay LOW until conversion
‘n’ is completed and the internal output register has been
updated. All new convert commands during BUSY LOW will
be ignored. CS and/or R/C must go HIGH before BUSY goes
HIGH, or a new conversion will be initiated without sufficient
time to acquire a new signal.
FIGURE 1a. Basic
±10V Operation, both Parallel and Serial
Output.
FIGURE 1b. Basic
±10V Operation with Serial Output.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
ADS7806
Parallel Output
200
66.5k
±10V
+5V
0.1
F
NC(1)
10
F
+
+5V
+
100
B6
B5
B4
LOW LOW LOW
B9
B8
B11
(MSB)
Pin 21
LOW
B10
B7
B1
B0
B3
Pin 21
HIGH
B2
LOW
(LSB)
2.2
F
++
2.2
F
Convert Pulse
BUSY
R/C
BYTE
40ns min
NOTE: (1) SDATA (pin 19) is always active.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
NC(1)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
ADS7806
Serial Output
200
66.5k
±10V
+5V
0.1
F
NC(1)
10
F
+
+5V
+
100
++
2.2
F
2.2
F
Convert Pulse
BUSY
40ns min
R/C
SDATA
DATACLK
NOTE: (1) These pins should be left unconnected.
They will be active when R/C is HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS7808U | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| ADS8382IBRHPT | 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PQCC28 |
| ADS8422IBPFBR | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| ADSP-2189NBSTZ-320 | 16-Bit, 80MIPS, 1.8V, 2 Serial Ports, Host Port, 192KB RAM; Package: 100 ld LQFP; No of Pins: 100; Temperature Range: Ind |
| ADSP-2189NKCAZ-320 | 16-Bit, 80MIPS, 1.8V, 2 Serial Ports, Host Port, 192KB RAM; Package: CHIP SCALE BGA; No of Pins: 144; Temperature Range: Comm. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS7806PBG4 | 功能描述:模數轉換器 - ADC Low-Power 12-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7806PG4 | 功能描述:模數轉換器 - ADC Low-Power 12-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7806U | 功能描述:模數轉換器 - ADC Low-Power 12-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS7806U | 制造商:Texas Instruments 功能描述:12BIT ADC LOW POWER SERIAL 7806 |
| ADS7806U/1K | 功能描述:模數轉換器 - ADC Low-Power 12-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。