- 您現在的位置：買賣IC網 > PDF目錄362144 > ADS774KP Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS774KP |
| 英文描述： | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| 中文描述： | 微處理器兼容采樣CMOS模擬數字轉換器 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 413K |
| 代理商： | ADS774KP |
ADS774
6
THEORY OF OPERATION
In the ADS774, the advantages of advanced CMOS technol-
ogy—high logic density, stable capacitors, precision analog
switches—and Burr-Brown’s state of the art laser trimming
techniques are combined to produce a fast, low power
analog-to-digital converter with internal sample/hold.
The charge-redistribution successive-approximation circuitry
converts analog input voltages into digital words.
A simple example of a charge-redistribution A/D converter
with only 3 bits is shown in Figure 1.
latch S
1
in position “R” or “G”. Similarly, the second
approximation is made by connecting S
2
to the reference and
S
3
to GND, and latching S
2
according to the output of the
comparator. After three successive approximation steps have
been made the voltage level at the comparator will be within
1/2LSB of GND, and a digital word which represents the
analog input can be determined from the positions of S
1
, S
2
and S
3
.
OPERATION
BASIC OPERATION
Figure 2 shows the minimum connections required to oper-
ate the ADS774 in a basic
±
10V range in the Control Mode
(discussed in detail in a later section.) The falling edge of a
Convert Command (a pulse taking pin 5 LOW for a mini-
mum of 25ns) both switches the ADS774 input to the hold
state and initiates the conversion. Pin 28 (STATUS) will
output a HIGH during the conversion, and falls only after the
conversion is completed and the data has been latched on the
data output pins (pins 16 to 27.) Thus, the falling edge of
STATUS on pin 28 can be used to read the data from the
conversion. Also, during conversion, the STATUS signal
puts the data output pins in a High-Z state and inhibits the
input lines. This means that pulses on pin 5 are ignored, so
that new conversions cannot be initiated during the conver-
sion, either as a result of spurious signals or to short-cycle
the ADS774.
The ADS774 will begin acquiring a new sample as soon as
the conversion is completed, even before the STATUS
output falls, and will track the input signal until the next
conversion is started. The ADS774 is designed to complete
a conversion and accurately acquire a new signal in 8.5
μ
s
max over the full operating temperature range, so that
conversions can take place at a full 117kHz.
CONTROLLING THE ADS774
The Burr-Brown ADS774 can be easily interfaced to most
microprocessor systems and other digital systems. The
microprocessor may take full control of each conversion, or
the converter may operate in a stand-alone mode, controlled
only by the R/C input. Full control consists of selecting an
8- or 12-bit conversion cycle, initiating the conversion, and
reading the output data when ready—choosing either 12 bits
all at once, or the 8 MSB bits followed by the 4 LSB bits in
a left-justified format. The five control inputs (12/8, CS, A
0
,
R/C, and CE) are all TTL/CMOS-compatible. The functions
of the control inputs are described in Table II. The control
function truth table is shown in Table III.
STAND-ALONE OPERATIO
N
For stand-alone operation, control of the converter is accom-
plished by a single control line connected to R/C. In this
mode CS and A
0
are connected to digital common and CE
and 12/8 are connected to +5V. The output data are
FIGURE 1. 3-Bit Charge Redistribution A/D.
INPUT SCALING
Precision laser-trimmed scaling resistors at the input divide
standard input ranges (0V to +10V, 0V to +20V,
±
5V or
±
10V) into levels compatible with the CMOS characteristics
of the internal capacitor array.
SAMPLING
While sampling, the capacitor array switch for the MSB
capacitor (S
1
) is in position “S”, so that the charge on the
MSB capacitor is proportional to the voltage level of the
analog input signal. The remaining array switches (S
2
and
S
3
) are set to position “G”. Switch S
C
is closed, setting the
comparator input offset to zero.
CONVERSION
When a conversion command is received, switch S
1
is
opened to trap a charge on the MSB capacitor proportional
to the analog input level at the time of the sampling com-
mand, and switch S
is opened to float the comparator input.
The charge trapped in the capacitor array can now be moved
between the three capacitors in the array by connecting
switches S
1
, S
2
, and S
3
to positions “R” (to connect to the
reference) or “G” (to connect to GND), thus changing the
voltage generated at the comparator input.
During the first approximation, the MSB capacitor is con-
nected through switch S
1
to the reference, while switches S
2
and S
3
are connected to GND. Depending on whether the
comparator output is HIGH or LOW, the logic will then
C
R
G
2C
R
G
4C
R
G
+
–
S
3
S
2
S
1
S
C
Comparator
L
o
g
i
c
Reference
Input
S
Signal
Analog
Input
Out
相關PDF資料 |
PDF描述 |
|---|---|
| ADS774KU | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS774JU | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7800 | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7800KP | Bus LVDS 2x2 Crosspoint/Repeater |
| ADS7800AH | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS774KP | 制造商:Texas Instruments 功能描述:A/D Converter (A-D) IC |
| ADS774KP-4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADS774KPG4 | 功能描述:模數轉換器 - ADC Microproc-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS774KU | 功能描述:模數轉換器 - ADC Mcrprcsr-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS774KU/1K | 功能描述:模數轉換器 - ADC Mcrprcsr-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。