- 您現在的位置：買賣IC網 > PDF目錄362144 > ADS774KP Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS774KP |
| 英文描述： | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| 中文描述： | 微處理器兼容采樣CMOS模擬數字轉換器 |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 413K |
| 代理商： | ADS774KP |
ADS774
10
FIGURE 7. 12-Bit Data Format for 8-Bit Systems.
12/8
A
STATUS
DB11 (MSB)
DB0 (LSB)
Digital Common
O
ADS774
28
27
26
25
24
23
22
21
20
19
18
17
16
15
2
4
Data
Bus
Address
Bus
A
O
S/H CONTROL MODE
AND ADC774 EMULATION MODE
The Emulation Mode allows the ADS774 to be dropped into
most existing ADC774 sockets without changes to other
system hardware or software. In existing sockets, the analog
input is held stable during the conversion period so that
accurate conversions can proceed, but the input can change
rapidly at any time before the conversion starts. The Emula-
tion Mode uses the stability of the analog input during the
conversion period to both acquire and convert in a maximum
of 8
μ
s (8.5
μ
s over temperature.) In fact, system throughput
can be increased, since the input to the ADS774 can start
slewing before the end of a conversion (after the acquisition
time), which is not possible with existing ADC774s.
The Control Mode is provided to allow full use of the
internal sample/hold, eliminating the need for an external
sample/hold in most applications. As compared with sys-
tems using separate sample/hold and A/D, the ADS774 in
the Control Mode also eliminates the need for one of the
control signals, usually the convert command. The com-
mand that puts the internal sample/hold in the hold state
also initiates a conversion, reducing timing constraints in
many systems.
The basic difference between these two modes is the
assumptions about the state of the input signal both before
and during the conversion. The differences are shown in
Figure 9 and Table VI. In the Control Mode, it is assumed
that during the required 1.4
μ
s acquisition time the signal is
not changing faster than the ADS774 can track. No assump-
tion is made about the input level after the convert command
arrives, since the input signal is sampled and conversion
begins immediately after the convert command. This means
that a convert command can also be used to switch an input
multiplexer or change gains on a programmable gain ampli-
fier, allowing the input signal to settle before the next
acquisition at the end of the conversion. Because aperture
jitter is minimized in the Control Mode, a high input fre-
quency can be converted without an external sample/hold.
In the Emulation Mode, a delay time is introduced between
the convert command and the start of conversion to allow the
ADS774 enough time to acquire the input signal before
converting. This increases the effective aperture delay time
from 0.02
μ
s to 1.6
μ
s, but allows the ADS774 to replace the
ADC774 in most circuits without additional changes. In
designs where the input to the ADS774 is changing rapidly
in the 200ns prior to a convert command, system perfor-
mance may be enhanced by delaying the convert command
by 200ns.
When using the ADS774 in the Emulation Mode to replace
existing converters in current designs, a sample/hold ampli-
fier often precedes the converter. In these cases, no addi-
tional delay in the convert command will be needed. The
existing sample/hold will not be slewing excessively when
going from the sample mode to the hold mode prior to a
conversion.
In both modes, as soon as the conversion is completed the
internal sample/hold circuit immediately begins slewing to
track the input signal.
FIGURE 8. Connection to an 8-Bit Bus.
Processor
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
Converter
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
0
0
0
0
Word 1
Word 2
相關PDF資料 |
PDF描述 |
|---|---|
| ADS774KU | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS774JU | Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER |
| ADS7800 | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
| ADS7800KP | Bus LVDS 2x2 Crosspoint/Repeater |
| ADS7800AH | 12-Bit 3ms Sampling ANALOG-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS774KP | 制造商:Texas Instruments 功能描述:A/D Converter (A-D) IC |
| ADS774KP-4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADS774KPG4 | 功能描述:模數轉換器 - ADC Microproc-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS774KU | 功能描述:模數轉換器 - ADC Mcrprcsr-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS774KU/1K | 功能描述:模數轉換器 - ADC Mcrprcsr-Compatible Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。