- 您現在的位置：買賣IC網 > PDF目錄366333 > ADNS-6130-001 (Avago Technologies Ltd.) High Performance Laser Mouse Bundles PDF資料下載
參數資料
| 型號： | ADNS-6130-001 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | High Performance Laser Mouse Bundles |
| 中文描述： | 高性能激光鼠標捆綁 |
| 文件頁數： | 7/52頁 |
| 文件大?。?/td> | 997K |
| 代理商： | ADNS-6130-001 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
7
Parameter
Laser output power
Symbol
LOP
Minimum
Maximum
716
Units
uW
Notes
Per conditions above
Single Fault Detection
ADNS-6010 is able to detect a short circuit, or fault,
condition at the RBIN and XY_LASER pins, which could
lead to excessive laser power output. A low resistance
path to ground on either of these pins will trigger the
fault detection circuit, which will turn off the laser drive
current source and set the LASER_NEN output high.
When used in combination with external components
as shown in the block diagram below, the system will
prevent excess laser power for a single short to ground
at RBIN or XY_LASER by shutting off the laser. Refer to the
PC board layout notes for recommendations to reduce
the chance of high resistance paths to ground existing
due to PC board contamination.
In addition to the continuous fault detection described
above, an additional test is executed automatically
whenever the LP_CFG0 register is written to. This test
will check for a short to ground on the XY_LASER pin,
a short to VDD3 on the XY_LASER pin, and will test the
fault detection circuit on the XY_LASER pin.
Figure 6. Single Fault Detection and Eye-safety Feature Block Diagram
RBIN
LASER_NEN
XY_LASER
GND
ADNS-6010
LASER
DRIVER
VDD3
LASER
Microcontroller
RESET
NPD
voltage sense
current set
VDD3
fault control
block
LASER Output Power
The laser beam output power as measured at the navi-
gation surface plane is specified below. The following
conditions apply:
1. The system is adjusted according to the above pro-
cedure.
2. The system is operated within the recommended op-
erating temperature range.
3. The VDD3 value is no greater than 50mV above its
value at the time of adjustment.
4. No allowance for optical power meter accuracy is as-
sumed.
Disabling the LASER
LASER_NEN is connected to the base of a PNP transistor
which when ON connects V
DD3
to the LASER. In normal
operation, LASER_NEN is low. In the case of a fault con-
dition (ground at XY_LASER or RBIN), LASER_NEN goes
high to turn the transistor off and disconnect V
DD3
from
the LASER.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-6230-001 | High Performance Laser Mouse Bundles |
| ADNV-6340 | High Performance Laser Mouse Bundles |
| ADNK-3080 | High-Performance Optical Mouse Sensor |
| ADNS-3080 | High-Performance Optical Mouse Sensor |
| ADNS-3150-001 | Optical Mouse Designer’s Kit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-6150 | 功能描述:光學導航傳感器 Small Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6160-001 | 功能描述:光學導航傳感器 Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6170-002 | 功能描述:光學導航傳感器 Wide Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6180-001 | 功能描述:光學導航傳感器 Trim lens for A7700 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-6180-002 | 功能描述:光學導航傳感器 Wide Trim Lens for A7700 RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。