- 您現在的位置：買賣IC網 > PDF目錄366333 > ADNS-5030 (Avago Technologies Ltd.) Low Power Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNS-5030 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | Low Power Optical Mouse Sensor |
| 中文描述： | 低功率光學鼠標傳感器 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 366K |
| 代理商： | ADNS-5030 |
Figure 5. Exploded view drawing.
PCB Assembly Considerations
1. Insert the sensor and all other electrical components
into PCB.
2. Insert the LED into the assembly clip and bend the leads
90 degrees.
3. Insert the LED clip assembly into PCB.
4. Wave solder the entire assembly in a no-wash solder
process utilizing solder fixture. The solder fixture is
needed to protect the sensor during the solder process.
It also sets the correct sensor-to-PCB distance as the
lead shoulders do not normally rest on the PCB surface.
The fixture should be designed to expose the sensor
leads to solder while shielding the optical aperture
from direct solder contact.
5. Place the lens onto the base plate.
6. Remove the protective kapton tape from optical
aperture of the sensor. Care must be taken to keep
contaminants from entering the aperture. Recommend
not to place the PCB facing up during the entire mouse
assembly process. Recommend to hold the PCB first
vertically for the kapton removal process.
7. Insert PCB assembly over the lens onto the base plate
aligning post to retain PCB assembly. The sensor
aperture ring should self-align to the lens.
8. The optical position reference for the PCB is set by the
base plate and lens. Note that the PCB motion due to
button presses must be minimized to maintain optical
alignment.
9. Install mouse top case. There MUST be a feature in
the top case to press down onto the PCB assembly to
ensure all components are interlocked to the correct
vertical height.
Figure 6. Block diagram of ADNS-5030 optical mouse sensor.
P
S
IMAGE ARRAY
DSP
OSCILLATOR
LED DRIVE
XY_LED
GND
VDD3
NCS
ADNS-5030
SCLK
MOSI
MISO
NRESET
ADNS-5100 (LENS)
CUSTOMER SUPPLIED PCB
HLMP-ED80 (LED)
ADNS-5200 (LED CLIP)
SENSOR
CUSTOMER SUPPLIED BASE PLATE
WITH RECOMMENDED ALIGNMENT
FEATURES PER IGES DRAWING
相關PDF資料 |
PDF描述 |
|---|---|
| ADNS-5100 | Solid-State Optical Mouse Lens |
| ADNS-5100-001 | Solid-State Optical Mouse Lens |
| ADPDC2BB4AW | General Purpose Snap-acting Switches |
| ADGGF3B14AC | General Purpose Snap-acting Switches |
| ADGGF3B14AW | General Purpose Snap-acting Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-5050 | 功能描述:光學導航傳感器 Navigation Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5060 | 功能描述:光學導航傳感器 Navigation Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5070 | 功能描述:光學導航傳感器 USB/PS2 LED Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5090 | 功能描述:光學導航傳感器 Wireless Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-5095 | 功能描述:光學導航傳感器 Wireless Optical Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發(fā)布緊急采購，3分鐘左右您將得到回復。