- 您現在的位置：買賣IC網 > PDF目錄375260 > ADNS-2051 Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNS-2051 |
| 英文描述： | Optical Mouse Sensor |
| 中文描述： | 光學鼠標傳感器 |
| 文件頁數： | 4/40頁 |
| 文件大小： | 454K |
| 代理商： | ADNS-2051 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
4
PCB Assembly Considerations
1.
Insert the sensor and all
other electrical components
into PCB.
2.
Bend the LED leads 90
°
and
then insert the LED into the
assembly clip until the snap
feature locks the LED base.
3.
Insert the LED/clip assembly
into PCB.
4.
Wave Solder the entire as-
sembly in a no-wash solder
process utilizing solder fix-
ture. The solder fixture is
needed to protect the sensor
during the solder process.
The fixture should be de-
signed to expose the sensor
leads to solder while shield-
ing the optical aperture from
direct solder contact. The
solder fixture is also used to
set the reference height of
the sensor to the PCB top
during wave soldering (Note:
DO NOT remove the kapton
tape during wave soldering).
Place the lens onto the base
plate.
Remove the protective
kapton tape from optical
aperture of the sensor. Care
must be taken to keep con-
taminants from entering the
aperture. It is recommended
not to place the PCB facing
up during the entire mouse
assembly process. The PCB
should be held vertically
during the kapton removal
process.
5.
6.
7.
Insert PCB assembly over the
lens onto the base plate align-
ing post to retain PCB assem-
bly. The sensor aperture ring
should self-align to the lens.
The optical position refer-
ence for the PCB is set by the
base plate and lens. Note that
the PCB motion due to button
presses must be minimized to
maintain optical alignment.
Install mouse top case. There
MUST be a feature in the top
case to press down onto the
clip to ensure all components
are interlocked to the correct
vertical height.
8.
9.
Figure 5. Exploded view drawing.
HDNS-2200 (CLIP)
HLMP-ED80-XXXXX (LED)
ADNS-2051 (SENSOR)
CUSTOMER SUPPLIED PCB
HDNS-2100 (LENS)
CUSTOMER SUPPLIED BASE PLATE
WITH RECOMMENDED ALIGNMENT
FEATURES PER IGES DRAWING
相關PDF資料 |
PDF描述 |
|---|---|
| ADP1109A | Micropower Low Cost Fixed 3.3 V, 5 V, 12 V and Adjustable DC-to-DC Converter(微功耗,低成本固定或可調輸出DC-DC轉換器) |
| ADP1109 | Micropower DC-DC Converter(可調/固定輸出,微功耗DC-DC轉換器) |
| ADP1147-3.3 | High Efficiency Step-Down Switching Regulator Controllers(高效率步降開關穩壓控制器) |
| ADP1147-5 | High Efficiency Step-Down Switching Regulator Controllers(高效率步降開關穩壓控制器) |
| ADP1148-5 | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNS-2080 | 功能描述:光學導航傳感器 LED Sensor RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-2120 | 功能描述:光學導航傳感器 Round Mouse Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-2120-001 | 功能描述:光學導航傳感器 Trim Mouse Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-2220 | 功能描述:光學導航傳感器 Black Optical Mouse Clip RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNS-2220-001 | 功能描述:光學導航傳感器 Clear Optical Mouse Clip RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。