- 您現在的位置：買賣IC網 > PDF目錄362139 > ADNB-3081 High-performance Optical Mouse Sensor PDF資料下載
參數資料
| 型號： | ADNB-3081 |
| 英文描述： | High-performance Optical Mouse Sensor |
| 中文描述： | 高性能的光學鼠標傳感器 |
| 文件頁數： | 15/40頁 |
| 文件大小： | 530K |
| 代理商： | ADNB-3081 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
15
Synchronous Serial Port
The synchronous serial port is
used to set and read
parameters in the ADNS-3080,
and to read out the motion
information. The serial port is
also used to load SROM data
into the ADNS-3080.
The port is a four-wire, serial
port. The host micro-
controller always initiates
communication; the ADNS-
3080 never initiates data
transfers. The serial port
cannot be activated while the
chip is in power down mode
(NPD low) or reset (RESET
high). SCLK, MOSI, and NCS
may be driven directly by a
3.3V output from a micro-
controller, or they may be
placed in an open drain
configuration by enabling on-
chip pull-up current sources.
The open drain drive allows
the use of a 5V micro-
controller without any level
shifting components. The port
Chip Select Operation
The serial port is activated
after NCS goes low. If NCS is
raised during a transaction,
the entire transaction is
aborted and the serial port
will be reset. This is true for
all transactions including
SROM download. After a
transaction is aborted, the
normal address-to-data or
transaction-to-transaction
delay is still required before
beginning the next transaction.
To improve communication
reliability, all serial
transactions should be framed
by NCS. In other words, the
port should not remain
enabled during periods of non-
use because ESD and EFT/B
events could be interpreted as
serial communication and put
the chip into an unknown
state. In addition, NCS must
be raised after each burst-
mode transaction is complete
to terminate burst-mode. The
port is not available for
further use until burst-mode is
terminated.
pins may be shared with other
SPI slave devices. When the
NCS pin is high, the inputs are
ignored and the output is tri-
stated.
The lines which comprise the
SPI port are:
SCLK: Clock input. It is always
generated by the master (the
micro- controller).
MOSI: Input data (Master Out/
Slave In).
MISO: Output data (Master In/
Slave Out).
NCS: Chip select input (active
low).
NCS needs to be low to
activate the serial port;
otherwise, MISO will be high-Z,
and MOSI & SCLK will be
ignored. NCS can also be used
to reset the serial port in case
of an error.
相關PDF資料 |
PDF描述 |
|---|---|
| ADNB-3082 | High-performance Optical Mouse Sensor |
| ADNS-2120 | High-performance Optical Mouse Sensor |
| ADNS-2120-001 | High-performance Optical Mouse Sensor |
| ADNS-2220 | High-performance Optical Mouse Sensor |
| ADNS-2220-001 | High-performance Optical Mouse Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADNB-3081-RLK | 功能描述:OPT SENSOR ROUND LENS K BIN LED RoHS:是 類別:傳感器，轉換器 >> 光學鼠標傳感器 系列:* 產品變化通告:Obsolescence Notificiation 15/Apr/2011 標準包裝:160 系列:* |
| ADNB-3081-RLP | 功能描述:OPT SENSOR ROUND LENS P BIN LED RoHS:是 類別:傳感器，轉換器 >> 光學鼠標傳感器 系列:* 產品變化通告:Obsolescence Notificiation 15/Apr/2011 標準包裝:160 系列:* |
| ADNB-3082 | 功能描述:光學導航傳感器 Bundle w/Trim Lens RoHS:否 制造商:Avago Technologies 工作電源電壓: 封裝 / 箱體: 最大工作溫度: 最小工作溫度: |
| ADNB-3082-TLK | 功能描述:OPT SENSOR TRIM LENS K BIN LED RoHS:是 類別:傳感器，轉換器 >> 光學鼠標傳感器 系列:* 產品變化通告:Obsolescence Notificiation 15/Apr/2011 標準包裝:160 系列:* |
| ADNB-3082-TLP | 功能描述:OPT SENSOR TRIM LENS P BIN LED RoHS:是 類別:傳感器，轉換器 >> 光學鼠標傳感器 系列:* 產品變化通告:Obsolescence Notificiation 15/Apr/2011 標準包裝:160 系列:* |
發布緊急采購，3分鐘左右您將得到回復。