- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1033ARQZ-REEL7 (ANALOG DEVICES INC) Thermal Monitor and Fan Speed (RPM) Controller PDF資料下載
參數資料
| 型號： | ADM1033ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Thermal Monitor and Fan Speed (RPM) Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 19/40頁 |
| 文件大?。?/td> | 1164K |
| 代理商： | ADM1033ARQZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADM1033
LAYOUT CONSIDERATIONS
Digital boards can be electrically noisy environments. Be sure to
protect the analog inputs from noise, particularly when
measuring the very small voltages from a remote diode sensor.
Take the following precautions:
Rev. 0 | Page 19 of 40
Place the ADM1033 as close as possible to the remote
sensing diode. A distance of 4 inches to 8 inches is
adequate, provided that the worst noise sources such as
clock generators, data/address buses, and CRTs are avoided.
Route the D+ and D tracks close together, in parallel, with
grounded guard tracks on each side. Provide a ground
plane under the tracks if possible.
Use wide tracks to minimize inductance and reduce noise
pickup. A minimum of 5 mil track width and spacing is
recommended.
Try to minimize the number of copper/solder joints, which
can cause thermocouple effects. Where copper/ solder
joints are used, make sure that they are in both the D+ and
D path and at the same temperature. Thermocouple
effects should not be a major problem because 1°C
corresponds to about 200 μV, and thermocouple voltages
are about 3 μV/°C of temperature difference. Unless there
are two thermocouples with a big temperature differential
between them, thermocouple voltages should be much less
than 200 μV.
5MIL
5MIL
5MIL
5MIL
5MIL
5MIL
5MIL
GND
D+
GND
D–
0
Figure 29. Arrangement of Signal Tracks
Place a 0.1 μF bypass capacitor close to the ADM1033.
If the distance to the remote sensor is more than 8 inches,
twisted pair cable is recommended. This works up to about
6 feet to 12 feet.
For very long distances (up to 100 feet), use shielded
twisted pair such as Belden #8451 microphone cable.
Connect the twisted pair to D+ and D and the shield to
GND, close to the ADM1033. Leave the remote end of the
shield unconnected to avoid ground loops.
Because the measurement technique uses switched current
sources, excessive cable and/or filter capacitance can affect the
measurement. When using long cables, the filter capacitor C1
may be reduced or removed. In any case, the total shunt
capacitance should never exceed 1000 pF.
Noise Filtering
For temperature sensors operating in noisy environments,
common practice is to place a capacitor across the D+ and D
pins to help combat the effects of noise. However, large capacitan-
ces affect the accuracy of the temperature measurement, leading
to a recommended maximum capacitor value of 1000 pF. While
this capacitor reduces the noise, it does not eliminate it, making it
difficult to use the sensor in a very noisy environment.
The ADM1033 has a major advantage over other devices when
it comes to eliminating the effects of noise on the external sen-
sor. The series resistance cancellation feature allows a filter to be
constructed between the external temperature sensor and the
part. The effect of any filter resistance seen in series with the remote
sensor is automatically cancelled from the temperature result.
The construction of a filter allows the ADM1033 and the
remote temperature sensor to operate in noisy environments.
Figure 30 shows a low-pass R-C-R filter with the following
values: R = 100 and C = 1 nF. This filtering reduces both
common-mode noise and differential noise.
0
D+
1nF
100
REMOTE
TEMPERATURE
SENSOR
D–
100
Figure 30. Filter Between Remote Sensor and ADM1033
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041ARQ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041 | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1033ARQZ-RL7 | 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1034ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Digital Serial (2-Wire) 16-Pin QSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL FAN CONTROLLER, SRC, SMBUS I.C. - Bulk |
| ADM1034ARQ-REEL | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1034ARQ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。