- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1030ARQ (ANALOG DEVICES INC) Intelligent Temperature Monitor and PWM Fan Controller PDF資料下載
參數資料
| 型號： | ADM1030ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Intelligent Temperature Monitor and PWM Fan Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 278K |
| 代理商： | ADM1030ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. 0
ADM1030
–20–
1. Run the fan at 53% PWM duty cycle in Software Mode. Clear
Bits 5 and 7 of Configuration Register 1 (Reg 0x00) to enter
PWM duty cycle mode. Write 0x08 to the Fan Speed Config
Register (Reg 0x22) to set the PWM output to 53% duty cycle.
2. Measure the fan RPM. This represents the fan RPM below
which the RPM mode will fail to operate. Do NOT program a
lower RPM than this value when using RPM Feedback mode.
3. Ensure that Speed Range, N, = 2 when using RPM Feed-
back mode.
Fans come in a variety of different options. One distinguishing
feature of fans is the number of poles that a fan has internally.
The most common fans available have four, six, or eight poles.
The number of poles the fan has generally affects the number of
pulses per revolution the fan outputs.
If the ADM1030 is used to drive fans other than 4-pole fans that
output 2 tach pulses/revolution, then the fan speed measurement
equation needs to be adjusted to calculate and display the cor-
rect fan speed, and also to program the correct count value in
RPM Feedback Mode.
FAN SPEED MEASUREMENT EQUATIONS
For a 4-pole fan (2 tach pulses/rev):
Fan RPM
= (
f
×
60)/
Count
×
N
For a 6-pole fan (3 tach pulses/rev):
Fan RPM
= (
f
×
60)/(
Count
×
N
×
1.5)
For an 8-pole fan (4 tach pulses/rev):
Fan RPM
= (
f
×
60)/(
Count
×
N
×
2)
If in doubt as to the number of poles the fans used have, or the
number of tach output pulses/rev, consult the fan manufacturer’s
data sheet, or contact the fan vendor for more information.
FAN DRIVE USING PWM CONTROL
The external circuitry required to drive a fan using PWM con-
trol is extremely simple. A single NMOS FET is the only drive
transistor required. The specifications of the MOSFET depend
on the maximum current required by the fan being driven. Typi-
cal notebook fans draw a nominal 170 mA, and so SOT devices
can be used where board space is a constraint. If driving several
fans in parallel from a single PWM output, or driving larger
server fans, the MOSFET will need to handle the higher current
requirements. The only other stipulation is that the MOSFET
should have a gate voltage drive, V
GS
< 3.3 V, for direct inter-
facing to the PWM_OUT pin. The MOSFET should also have
a low on-resistance to ensure that there is not significant volt-
age drop across the FET. This would reduce the maximum
operating speed of the fan.
Figure 18 shows how a 3-wire fan may be driven using
PWM control.
+V
Q1
NDT3055L
PWM_OUT
5V OR 12V
FAN
TACH/AIN
ADM1030
3.3V
10k
TYPICAL
TACH
10k
TYPICAL
3.3V
Figure 18. Interfacing the ADM1030 to a 3-Wire Fan
The NDT3055L n-type MOSFET was chosen since it has 3.3V
gate drive, low on-resistance, and can handle 3.5 A of current.
Other MOSFETs may be substituted based on the system’s fan
drive requirements.
+V
Q1
NDT3055L
PWM_OUT
5V OR 12V
FAN
TACH/AIN
ADM1030
3.3V
10k
TYPICAL
TACH
R
(2 TYPICAL)
0.01 F
Figure 19. Interfacing the ADM1030 to a 2-Wire Fan
Figure 19 shows how a 2-wire fan may be connected to the
ADM1030. This circuit allows the speed of the 2-wire fan to
be measured even though the fan has no dedicated Tach sig-
nal. A series R
SENSE
resistor in the fan circuit converts the fan
commutation pulses into a voltage. This is ac-coupled into
the ADM1030 through the 0.01
μ
F capacitor. On-chip signal
conditioning allows accurate monitoring of fan speed. For typical
notebook fans drawing approximately 170 mA, a 2
R
SENSE
value is suitable. For fans such as desktop or server fans, that
draw more current, R
SENSE
may be reduced. The smaller R
SENSE
is the better, since more voltage will be developed across the
fan, and the fan will spin faster. Figure 20 shows a typical plot
of the sensing waveform at the TACH/AIN pin. The most
important thing is that the negative-going spikes are more than
250 mV in amplitude. This will be the case for most fans when
R
SENSE
= 2
. The value of R
SENSE
can be reduced as long as
the voltage spikes at the TACH/AIN pin are greater than 250 mV.
This allows fan speed to be reliably determined.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL7 | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1030ARQ-REEL | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQ-REEL7 | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1030ARQZ-REEL | 功能描述:板上安裝溫度傳感器 TDM PWM FAN CTRLRS IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1030ARQZ-REEL7 | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。