- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026 (Analog Devices, Inc.) Complete Thermal and System Management Controller PDF資料下載
參數資料
| 型號： | ADM1026 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Complete Thermal and System Management Controller |
| 中文描述： | 完整的熱和系統管理控制器 |
| 文件頁數： | 27/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
Chassis Intrusion Input
The chassis intrusion input is an active high input intended for
detection and signaling of unauthorized tampering with the
system. When this input goes high, the event is latched in Bit 6
of Status Register 4, and an interrupt is generated. The bit
remains set until cleared by writing a 1 to CI clear, Bit 1 of
Configuration Register 3 (05h), as long as battery voltage is
connected to the V
BAT
input. The CI clear bit itself is cleared by
writing a 0 to it.
Rev. A | Page 27 of 56
The CI input detects chassis intrusion events even when the
ADM1026 is powered off (provided battery voltage is applied to
V
BAT
) but does not immediately generate an interrupt. Once a
chassis intrusion event is detected and latched, an interrupt is
generated when the system is powered on.
The actual detection of chassis intrusion is performed by an
external circuit that detects, for example, when the cover has
been removed. A wide variety of techniques may be used for the
detection, for example:
A microswitch that opens or closes when the cover is
removed.
A reed switch operated by magnet fixed to the cover.
A hall-effect switch operated by magnet fixed to the cover.
A phototransistor that detects light when the cover is
removed.
The chassis intrusion input can also be used for other types of
alarm input. Figure 49 shows a temperature alarm circuit using
an AD22105 temperature switch sensor. This produces a low-
going output when the preset temperature is exceeded, so the
output is inverted by Q1 to make it compatible with the CI
input. Q1 can be almost any small-signal NPN transistor, or a
TTL or CMOS inverter gate may be used if one is available.
See the AD22105 data sheet on the Analog Devices, Inc.
SET.
V
CC
R
SET
AD22105
TEMPERATURE
SENSOR
6
CI
R1
10k
Q1
7
3
2
1
18
0
Figure 49. Using the CI Input with a Temperature Sensor
General-Purpose I/O Pins (Open Drain)
The ADM1026 has eight pins that are dedicated to general-
purpose logic input/output (Pins 1, 2, and 43 to 48), eight pins
that can be configured as general-purpose logic pins or fan
speed inputs (Pins 3 to 6, and 9 to 12), and one pin that can
be configured as GPIO16 or the bidirectional THERM pin
(Pin 42). The GPIO/FAN pins are configured as general-
purpose logic pins by setting Bits 0 to 7 of Configuration
Register 2 (Address 01h). Pin 42 is configured as GPIO16 by
setting Bit 0 of Configuration Register 3, or as the THERM
function by clearing this bit.
Each GPIO pin has four data bits associated with it, two bits in
one of the GPIO configuration registers (Addresses 08h to 0Bh),
one in the GPIO status registers (Addresses 24h and 25h), and
one in the GPIO mask registers (Addresses 1Ch and 1Dh)
Setting a direction bit = 1 in one of the GPIO configuration
registers makes the corresponding GPIO pin an output.
Clearing the direction bit to 0 makes it an input.
Setting a polarity bit = 1 in one of the GPIO configuration
registers makes the corresponding GPIO pin active high.
Clearing the polarity bit to 0 makes it active low.
When a GPIO pin is configured as an input, the corresponding
bit in one of the GPIO status registers is read-only, and is set
when the input is asserted (“asserted” may be high or low
depending on the setting of the polarity bit).
When a GPIO pin is configured as an output, the corresponding
bit in one of the GPIO status registers becomes read/write.
Setting this bit then asserts the GPIO output. (Here again,
“asserted” may be high or low depending on the setting of the
polarity bit.)
The effect of a GPIO status register bit on the INT output can
be masked out by setting the corresponding bit in one of the
GPIO mask registers. When the pin is configured as an output,
this bit is automatically masked to prevent the data written to
the status bit from causing an interrupt, with the exception of
GPIO16, which must be masked manually by setting Bit 7 of
Mask Register 4 (Reg 1Bh).
When configured as inputs, the GPIO pins may be connected to
external interrupt sources such as temperature sensors with
digital output. Another application of the GPIO pins would be
to monitor a processor’s voltage ID code (VID code).
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1026JST-REEL | Complete Thermal and System Management Controller |
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
| ADM1026JST | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026EBZEVB | 功能描述:BOARD EVAL FOR ADM1026 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1026JST | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。