- 您現在的位置：買賣IC網 > PDF目錄366333 > ADJD-J823 (Avago Technologies Ltd.) Color Management Controller with Integrated RGB Photosensor PDF資料下載
參數資料
| 型號： | ADJD-J823 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | Color Management Controller with Integrated RGB Photosensor |
| 中文描述： | 色彩管理控制器集成RGB光 |
| 文件頁數： | 5/18頁 |
| 文件大?。?/td> | 275K |
| 代理商： | ADJD-J823 |
5
High Level Description
A hardware reset (by asserting XRST) should be performed
before starting any operation. It is assumed that factory
calibration was performed prior deployment of ADJD-J823.
Calibration is discussed at the end of this section.
The user controls and configures the device by program-
ming a set of internal registers through a serial interface. At
the start of application, the following register data must be
written to it:
Frequency registers
Setup data
Calibration data
Bright and color input registers.
The register data is usually gathered during a calibration
process which is performed once in manufacturing. Factory
calibration is needed at a system level to map the integrated
tri-color sensor’s reading (device dependent) with a standard
device independent color space.
Once the register data is entered, the feedback operation
begins; the device starts to sample the RGB sensor using
the internal ADC. That data is compared to a user-controlled
color point target. The PWM duty factor for each channel is
adjusted in response to any error signal generated by that
comparison operation.
Thus, the actual color produced by the LEDs is maintained
close to the target.
There are three methods to operate the device. They are
differentiated by the technique in which the register data
is stored and used. The three figures below describe the
methods. NVPROM stands for Non-Volatile Programmable
Read-Only Memory such as an EEPROM.
Independent NVPROM
The NVPROM is independent from the device. During
factory calibration, the host must read the register data
from the device and write it to the NVPROM. At the start
of application, the host must read the register data from
the NVPROM and write it back to the device, after which
the device will wait for further instructions in normal
mode.
DEVICE
NVPROM
HOST
CONTROLLER
SDASLV
SCLSLV
DEVICE
NVPROM
SDAPROM
SCLPROM
HOST
CONTROLLER
SDASLV
SCLSLV
DEVICE
NVPROM
SDAPROM
SCLPROM
Dedicated NVPROM in Standalone Mode
A dedicated NVPROM is connected to the device. During
factory calibration, the host can instruct the device to
upload the register data to the NVPROM. The difference
versus Interactive Mode is that, in application, the device
itself will download the register data and immediately
after, enter normal mode. Then, it will start driving the
PWM channels to achieve a default target color point.
The default color point is programmed after factory
calibration. A host controller is not necessary during ap-
plication. The serial interface protocol between device
and NVPROM is hard coded. So, a standard NVPROM
such as a serial I2C EEPROM with address 0x50 (7-bit)
must be used.
Dedicated NVPROM in Interactive Mode
A dedicated NVPROM is connected to the device. During
factory calibration, the host can instruct the device to
upload the register data to the NVPROM. At the start of
application, the host can instruct the device to download
the register data from the NVPROM, after which the de-
vice will wait for further instructions in normal mode. The
serial interface protocol between device and NVPROM
is hard coded. A standard NVPROM such as a serial I2C
EEPROM with address 0x50 (7-bit) must be used.
相關PDF資料 |
PDF描述 |
|---|---|
| ADJD-MJ61 | Automotive Relays; V23086R1801A403-EV-USBX ( Tyco Electronics ) |
| ADJD-MJ50 | High Performance RGB LED Light Source |
| ADJD-MJ51 | High Performance RGB LED Light Source |
| ADJD-MJ60 | High Performance RGB LED Light Source |
| ADJD-S312-CR999 | Miniature Surface-Mount RGB Digital Color Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADJD-MJ50 | 功能描述:LED照明模塊 RGB LED Light Strip Top Emitting RoHS:否 制造商:Cree, Inc. 產品:LED Modules LED 數量:1 照明顏色:Neutral White 射束角:96 deg 波長/色溫:3500 K 光強度: 光通量:3000 lm 寬度: 長度:88.2 mm 系列: 封裝:Bulk |
| ADJD-MJ51 | 功能描述:LED照明模塊 RGB LED Light Strip Top Emitting w/cable RoHS:否 制造商:Cree, Inc. 產品:LED Modules LED 數量:1 照明顏色:Neutral White 射束角:96 deg 波長/色溫:3500 K 光強度: 光通量:3000 lm 寬度: 長度:88.2 mm 系列: 封裝:Bulk |
| ADJD-MJ60 | 功能描述:LED照明模塊 RGB LED Light Strip Side Emitting RoHS:否 制造商:Cree, Inc. 產品:LED Modules LED 數量:1 照明顏色:Neutral White 射束角:96 deg 波長/色溫:3500 K 光強度: 光通量:3000 lm 寬度: 長度:88.2 mm 系列: 封裝:Bulk |
| ADJD-MJ61 | 功能描述:LED照明模塊 RGB LED Light Strip RoHS:否 制造商:Cree, Inc. 產品:LED Modules LED 數量:1 照明顏色:Neutral White 射束角:96 deg 波長/色溫:3500 K 光強度: 光通量:3000 lm 寬度: 長度:88.2 mm 系列: 封裝:Bulk |
| ADJD-S311-CR999 | 功能描述:圖像傳感器和彩色傳感器 RGB Color Sensor RoHS:否 制造商:Avago Technologies 類型:Color Sensors 工作電源電壓:2.5 V 封裝 / 箱體: 圖象大小: 顏色讀出:Color 最大工作溫度:+ 70 C 最小工作溫度:- 25 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。