參數資料
型號: ADC12191CIVT
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: ADC
英文描述: 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold
中文描述: 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32
封裝: TQFP-32
文件頁數: 10/16頁
文件大?。?/td> 278K
代理商: ADC12191CIVT
Specification Definitions
(Continued)
FULL SCALE ERROR
is the difference between the input
voltage just causing a transition to positive full scale and
V
REF
-1.5 LSB.
INTEGRAL NON-LINEARITY (INL)
is a measure of the de-
viation of each individual code from a line drawn from nega-
tive full scale (
1
2
LSB below the first code transition) through
positive full scale (1
1
2
LSB above the last code transition).
The deviation of any given code from this straight line is
measured from the center of that code value.
INTERMODULATION DISTORTION (IMD)
is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to theADC input at the same time.
It is defined as the ratio of the power in the intermodulation
products to the total power in the original frequencies. IMD is
usually expressed in dB.
PIPELINE DELAY (LATENCY)
is the number of clock cycles
between initiation of conversion and the availability of that
conversion result at the output. New data is available at ev-
ery clock cycle, but the data lags the conversion by the pipe-
line delay.
Timing Diagrams
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SI-
NAD)
is the ratio expressed in dB, of the rms value of the in-
put signal to the rms value of all of the other spectral compo-
nents below half the clock frequency, including harmonics
but excluding dc.
SIGNAL TO NOISE RATIO (SNR)
is the ratio of the rms
value of the input signal to the rms value of the other spectral
components below one-half the sampling frequency, not in-
cluding harmonics or dc.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
is the differ-
ence, expressed in dB, between the rms values of the input
signal and the peak spurious signal, where a spurious signal
is any signal present in the output spectrum that is not
present at the input.
TOTAL HARMONIC DISTORTION (THD)
is the ratio of the
rms total of the first six harmonic components, to the rms
value of the input signal.
ZERO ERROR
is the difference between the ideal input volt-
age (
1
2
LSB) and the actual input voltage that causes an out-
put code transition from zero to one.
DS101040-21
FIGURE 3. Data Output Timing
A
www.national.com
10
相關PDF資料
PDF描述
ADC12191 12-Bit, 10 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold(12位10 MHz可自行校對的管線式帶內部采樣和保持功能A/D轉換器)
ADC121S625 12-Bit, 50 ksps to 200 ksps, Differential Input, Micro Power Sampling A/D Converter
ADC121S625CIMM 12-Bit, 50 ksps to 200 ksps, Differential Input, Micro Power Sampling A/D Converter
ADC121S021 Single Channel, 500 kSPS, 8-Bit A/D Converter
ADC121S051 Single Channel, 500 kSPS, 8-Bit A/D Converter
相關代理商/技術參數
參數描述
ADC121C021 制造商:NSC 制造商全稱:National Semiconductor 功能描述:I2C-Compatible, 12-Bit Analog-to-Digital Converter (ADC) with Alert Function
ADC121C021CIMK 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC121C021CIMK/NOPB 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADC121C021CIMKX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:I2C-Compatible, 12-Bit Analog-to-Digital Converter (ADC) with Alert Function
ADC121C021CIMKX/NOPB 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32