- 您現在的位置：買賣IC網 > PDF目錄378280 > ADC10030 (National Semiconductor Corporation) 10-Bit, 30 MSPS, 125 mW A/D Converter with Internal Sample and Hold PDF資料下載
參數資料
| 型號： | ADC10030 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10-Bit, 30 MSPS, 125 mW A/D Converter with Internal Sample and Hold |
| 中文描述： | 10位，30 MSPS的，125毫瓦的A / D內部采樣與保持器 |
| 文件頁數： | 14/17頁 |
| 文件大小： | 417K |
| 代理商： | ADC10030 |
Applications Information
(Continued)
3.0 POWER SUPPLY CONSIDERATIONS
A/D converters draw sufficient transient current to corrupt
their own power supplies if not adequately bypassed. A
10 μF to 50 μF tantalum or aluminum electrolytic capacitor
should be placed within an inch (2.5 centimeters) of the A/D
power pins, with a 0.1 μF ceramic chip capacitor placed as
close as possible to each of the converter’s power supply
pins. Leadless chip capacitors are preferred because they
have low lead inductance.
While a single voltage source should be used for the analog
and digital supplies of the ADC10030, these supply pins
should be well isolated from each other to prevent any digital
noise from being coupled to the analog power pins. A choke
or ferrite bead is recommended between the analog and
digital supply lines, with a ceramic capacitor close to the
analog supply pin.
The converter digital supply should
not
be the supply that is
used for other digital circuitry on the board. It should be the
same supply used for the ADC10030 analog supply.
As is the case with all high-speed converters, the ADC10030
should be assumed to have little high frequency power sup-
ply rejection. A clean analog power source should be used.
No pin should ever have a voltage on it that is more than
300 mV in excess of the supply voltages or below ground,
not even on a transient basis. This can be a problem upon
application of power to a circuit. Be sure that the supplies to
circuits driving the CLK, PD, OE, analog input and reference
pins do not come up any faster than does the voltage at the
ADC10030 power pins.
4.0 THE ADC10030 CLOCK
Although the ADC10030 is tested and its performance is
guaranteed with a 27 MHz clock, it typically will function with
clock frequencies from 1 MHz to 30 MHz. Performance is
best if the clock rise and fall times are 4 ns or less and if the
clock line is terminated with a series RC of about 100
and
47 pF near the clock input pin, as shown in Figure 6
5.0 LAYOUT AND GROUNDING
Proper routing of all signals and proper ground techniques
are essential to ensure accurate conversion. Separate ana-
log and digital ground planes are required to meet data sheet
limits. The analog ground plane should be low impedance
and free of noise from other parts of the system.
Each bypass capacitor should be located as close to the ap-
propriate converter pin as possible and connected to the pin
and the appropriate ground plane with short traces. The ana-
log input should be isolated from noisy signal traces to avoid
coupling of spurious signals into the input.Any external com-
ponent (e.g., a filter capacitor) connected between the con-
verter’s input and ground should be connected to a very
clean point in the analog ground return.
DS101064-20
FIGURE 6. Setting Precision Reference Voltages
A
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| ADC10040 | ECONOLINE: REC3-S_DRW(Z)/H4,H6 - Safety standards and approval: EN 60950 certified, rated for 250VAV (LVD test report)- Applied for Ul 1950 Component Recognised Certification- 3W DIP Package- 4kVDC & 6kVDC Isolation- Regulated Output- Continuous Short Circiut Protection Auto-Restarting |
| ADC10040CIMT | 10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter |
| ADC10040CIMTX | 10-Bit, 40 MSPS, 3V, 55.5 mW A/D Converter |
| ADC1005 | 10-BIT uP COMPATIBLE A/D CONVERTERS |
| ADC1005BCJ | 10-BIT uP COMPATIBLE A/D CONVERTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC10030CIVT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit, 30 MSPS, 125 mW A/D Converter with Internal Sample and Hold |
| ADC10030CIVT/NOPB | 功能描述:IC ADC 10BIT 32-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| ADC10030EVAL | 功能描述:BOARD EVALUATION FOR ADC10030 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADC1003S030 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz, with voltage regulator |
| ADC1003S030/DB | 功能描述:數據轉換 IC 開發工具 ADC DEMO BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。