- 您現在的位置：買賣IC網 > PDF目錄378278 > ADC08200 (National Semiconductor Corporation) 8-Bit, 20 MSPS to 200 MSPS, 1.05 mW/MSPS A/D Converter PDF資料下載
參數資料
| 型號： | ADC08200 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 8-Bit, 20 MSPS to 200 MSPS, 1.05 mW/MSPS A/D Converter |
| 中文描述： | 8位，20 MSPS的200 MSPS的，1.05毫瓦/ MSPS的A / D轉換 |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 537K |
| 代理商： | ADC08200 |
Applications Information
(Continued)
devices) to exhibit undershoot that goes more than a volt
below ground. A 51
resistor in series with the offending
digital input will usually eliminate the problem.
Care should be taken not to overdrive the inputs of the
ADC08200. Such practice may lead to conversion inaccura-
cies and even to device damage.
Attempting to drive a high capacitance digital data bus.
The more capacitance the output drivers must charge for
each conversion, the more instantaneous digital current is
required from V
and DR GND. These large charging cur-
rent spikes can couple into the analog section, degrading
dynamic performance. Buffering the digital data outputs (with
a 74AF541, for example) may be necessary if the data bus
capacitance exceeds 5 pF. Dynamic performance can also
be improved by adding 33
to 47
series resistors at each
digital output, reducing the energy coupled back into the
converter input pins.
Using an inadequate amplifier to drive the analog input.
As explained in Section 2.0, the capacitance seen at the
input alternates between 3 pF and 4 pF with the clock. This
dynamic capacitance is more difficult to drive than is a fixed
capacitance, and should be considered when choosing a
driving device.
Driving the V
pin or the V
pin with devices that can
not source or sink the current required by the ladder.
As
mentioned in Section 1.0, care should be taken to see that
any driving devices can source sufficient current into the V
RT
pin and sink sufficient current from the V
RB
pin. If these pins
are not driven with devices than can handle the required
current, these reference pins will not be stable, resulting in a
reduction of dynamic performance.
Using a clock source with excessive jitter, using an
excessively long clock signal trace, or having other
signals coupled to the clock signal trace.
This will cause
the sampling interval to vary, causing excessive output noise
and a reduction in SNR performance. The use of simple
gates with RC timing is generally inadequate as a clock
source.
A
www.national.com
17
相關PDF資料 |
PDF描述 |
|---|---|
| ADC08200CIMT | 8-Bit, 20 MSPS to 200 MSPS, 1.05 mW/MSPS A/D Converter |
| ADC0820 | 8-Bit High Speed μP Compatible A/D Converter with Track/Hold Function(8位高速μP兼容A/D轉換器帶跟蹤/保持功能) |
| ADC08234CIMF | IC,QUAD,UART,FIFO |
| ADC08238 | 16 A SPDT MINIATURE POWER RELAY |
| ADC08238BIN | 8-Bit 2 ms Serial I/O A/D Converters with MUX, Reference, and Track/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC08200_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit, 20 Msps to 200 Msps, Low Power A/D Converter with Internal Sample-and-Hold |
| ADC08200CIMT | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200CIMT/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200CIMTX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC08200CIMTX/HAPB | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。