參數資料
型號： ADAU1361BCPZ-R7
廠商： Analog Devices Inc
文件頁數： 26/80頁
文件大?。?/td> 0K
描述： IC CODEC 24B PLL 32LFCSP
標準包裝： 1,500
類型： 音頻編解碼器
數據接口： 串行
分辨率（位）： 24 b
ADC / DAC 數量： 2 / 2
三角積分調變： 無
電壓 - 電源，模擬： 1.8 V ~ 3.6 V
電壓 - 電源，數字： 1.8 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 帶卷 (TR)
ADAU1361
Rev. C | Page 32 of 80
AUTOMATIC LEVEL CONTROL (ALC)
The ADAU1361 contains a hardware automatic level control
(ALC). The ALC is designed to continuously adjust the PGA
gain to keep the recording volume constant as the input level
varies.
For optimal noise performance, the ALC uses the analog PGA
to adjust the gain instead of using a digital method. This ensures
that the ADC noise is not amplified at low signal levels.
Extremely small gain step sizes are used to ensure high audio
quality during gain changes.
To use the ALC function, the inputs must be applied either
differentially or pseudo-differentially to input pins LINN and
LINP, for the left channel, and RINN and RINP, for the right
channel. The ALC function is not available for the auxiliary line
input pins, LAUX and RAUX.
A block diagram of the ALC block is shown in Figure 36. The
ALC logic receives the ADC output signals and analyzes these
digital signals to set the PGA gain. The ALC control registers
are used to control the time constants and output levels, as
described in this section.
07
67
9-
0
24
RIGHT
ADC
LEFT
ADC
MUTE
SERIAL
PORTS
ALC
DIGITAL
ANALOG
INPUT
LEFT
I2C
CONTROL
ANALOG
INPUT
RIGHT
PGA
–12dB TO +35.25dB
0.75dB STEP SIZE
Figure 36. ALC Architecture
ALC PARAMETERS
The ALC function is controlled with the ALC control registers
(Address 0x4011 through Address 0x4014) using the following
parameters:
ALCSEL[2:0]: The ALC select bits are used to enable the
ALC and set the mode to left only, right only, or stereo. In
stereo mode, the greater of the left or right inputs is used
to calculate the gain, and the same gain is then applied to
both the left and right channels.
ALCTARG[3:0]: The ALC target is the desired input
recording level that the ALC attempts to achieve.
ALCATCK[3:0]: The ALC attack time sets how fast the
ALC starts attenuating after a sudden increase in input
level above the ALC target. Although it may seem that
the attack time should be set as fast as possible to avoid
clipping on transients, using a moderate value results in
better overall sound quality. If the value is too fast, the
ALC overreacts to very short transients, causing audible
gain-pumping effects, which sounds worse than using a
moderate value that allows brief periods of clipping on
transients. A typical setting for music recording is 384 ms.
A typical setting for voice recording is 24 ms.
ALCHOLD[3:0]: These bits set the ALC hold time. When
the output signal falls below the target output level, the
gain is not increased unless the output remains below the
target level for the period of time set by the hold time bits.
The hold time is used to prevent the gain from modulating
on a steady low frequency sine wave signal, which would
cause distortion.
ALCDEC[3:0]: The ALC decay time sets how fast the ALC
increases the PGA gain after a sudden decrease in input level
below the ALC target. A very slow setting can be used if the
main function of the ALC is to set a music recording level.
A faster setting can be used if the function of the ALC is to
compress the dynamic range of a voice recording. Using a
very fast decay time can cause audible artifacts such as noise
pumping or distortion. A typical setting for music recording
is 24.58 sec. A typical setting for voice recording is 1.54 sec.
ALCMAX[2:0]: The maximum ALC gain bits are used to
limit the maximum gain that can be programmed into the
ALC. This can be used to prevent excessive noise in the
recording for small input signals. Note that setting this
register to a low value may prevent the ALC from reaching
its target output level, but this behavior is often desirable to
achieve the best overall sound.
Figure 37 shows the dynamic behavior of the PGA gain for a
tone-burst input. The target output is achieved for three differ-
ent input levels, with the effect of attack, hold, and decay shown
in the figure. Note that for very small signals, the maximum PGA
gain may prevent the ALC from achieving its target level; in the
same way, for very large inputs, the minimum PGA gain may
prevent the ALC from achieving its target level (assuming that
the target output level is set to a very low value). The effects of
the PGA gain limit are shown in the input/output graph of
相關PDF資料
PDF描述
ADAU1373BCBZ-RL IC CODEC LP CLASS G HP 81WLCSP
ADAU1381BCPZ IC AUDIO CODEC STEREO LN 32LFCSP
ADAU1761BCPZ-RL IC SIGMADSP CODEC PLL 32LFCSP
ADAU1781BCPZ-RL7 IC SIGMADSP CODEC LN 32LFCSP
ADAU1961WBCPZ-R7 IC STEREO AUD CODEC LP 32LFCSP
相關代理商/技術參數
參數描述
ADAU1361BCPZ-RL 功能描述:IC CODEC 24B PLL 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR)
ADAU1372BCPZ 功能描述:General Purpose Interface 24 b I2C, SPI 40-LFCSP-WQ (6x6) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:有效 類型:通用 數據接口:I2C， SPI 分辨率（位）:24 b ADC/DAC 數:4 / 2 三角積分:是 信噪比，ADC/DAC（db）（典型值）:- 動態范圍，ADC/DAC（db）（典型值）:- 電壓 - 電源，模擬:1.71 V ~ 3.63 V 電壓 - 電源，數字:1.045 V ~ 1.98 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤，CSP 供應商器件封裝:40-LFCSP-WQ（6x6） 標準包裝:1
ADAU1372BCPZRL 功能描述:IC CODEC LP CLASS G HP 40LFCSP 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:Digi-Key 停止供應 類型:通用 數據接口:I2C， SPI 分辨率（位）:24 b ADC/DAC 數:4 / 2 三角積分:是 信噪比，ADC/DAC（db）（典型值）:- 動態范圍，ADC/DAC（db）（典型值）:- 電壓 - 電源，模擬:1.71 V ~ 3.63 V 電壓 - 電源，數字:1.045 V ~ 1.98 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤，CSP 供應商器件封裝:40-LFCSP-WQ（6x6） 標準包裝:1
ADAU1372BCPZ-RL 功能描述:General Purpose Interface 24 b I2C, SPI 40-LFCSP-WQ (6x6) 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:停產 類型:通用 數據接口:I2C， SPI 分辨率（位）:24 b ADC/DAC 數:4 / 2 三角積分:是 信噪比，ADC/DAC（db）（典型值）:- 動態范圍，ADC/DAC（db）（典型值）:- 電壓 - 電源，模擬:1.71 V ~ 3.63 V 電壓 - 電源，數字:1.045 V ~ 1.98 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤，CSP 供應商器件封裝:40-LFCSP-WQ（6x6） 標準包裝:1
ADAU1373BCBZ-R7 功能描述:IC CODEC LP W/HDPH AMP 81WLSCP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:PCM 數據接口:PCM 音頻接口 分辨率（位）:15 b ADC / DAC 數量:1 / 1 三角積分調變:是 S/N 比，標準 ADC / DAC (db):- 動態范圍，標準 ADC / DAC (db):- 電壓 - 電源，模擬:2.7 V ~ 3.3 V 電壓 - 電源，數字:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-VFBGA 供應商設備封裝:80-BGA MICROSTAR JUNIOR（5x5） 包裝:帶卷 (TR) 其它名稱:296-21257-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*