- 您現在的位置：買賣IC網 > PDF目錄11769 > AD9980KSTZ-80 (Analog Devices Inc)IC INTERFACE 8BIT ANALOG 80LQFP PDF資料下載
參數資料
| 型號： | AD9980KSTZ-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE 8BIT ANALOG 80LQFP |
| 標準包裝： | 90 |
| 應用： | 視頻 |
| 接口： | 模擬 |
| 電源電壓： | 3.13 V ~ 3.47 V |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
| 配用： | AD9980/PCBZ-ND - KIT EVALUATION AD9980 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9980
Preliminary Technical Data
Rev. 0 | Page 28 of 44
DETAILED 2-WIRE SERIAL CONTROL REGISTER DESCRIPTIONS
CHIP IDENTIFICATION
0x00
7:0
Chip Revision
An 8-bit register which represents the silicon revision.
PLL DIVIDER CONTROL
0x01
7:0
PLL Divide Ratio MSBs
The eight MSBs of the 12-bit PLL divide ratio PLLDIV.
The PLL derives a pixel clock from the incoming
Hsync signal. The pixel clock frequency is then
divided by an integer value, such that the output is
phase-locked to Hsync. This PLLDIV value
determines the number of pixel times (pixels plus
horizontal blanking overhead) per line. This is
typically 20% to 30% more than the number of active
pixels in the display.
The 12-bit value of the PLL divider supports divide
ratios from 2 to 4095 as long as the output frequency
is within range. The higher the value loaded in this
register, the higher the resulting clock frequency with
respect to a fixed Hsync frequency.
VESA has established some standard timing
specifications, which will assist in determining the
value for PLLDIV as a function of horizontal and
vertical display resolution and frame rate (see Table 9).
However, many computer systems do not conform
precisely to the recommendations and these numbers
should be used only as a guide. The display system
manufacturer should provide automatic or manual
means for optimizing PLLDIV. An incorrectly set
PLLDIV usually produces one or more vertical noise
bars on the display. The greater the error, the greater
the number of bars produced.
The power-up default value of PLLDIV is 1693.
PLLDIVM = 0x69, PLLDIVL = 0xDx.
The AD9980 updates the full divide ratio only when
the LSBs are written. Writing to this register by itself
does not trigger an update.
0x02
7:4
PLL Divide Ratio LSBs
The four LSBs of the 12-bit PLL divide ratio PLLDIV.
The power-up default value of PLLDIV is 1693.
PLLDIVM = 0x69, PLLDIVL = 0xDx.
CLOCK GENERATOR CONTROL
0x03
7:6
VCO Range Select
Two bits that establish the operating range of the clock
generator. VCORNGE must be set to correspond to
the desired operating frequency (incoming pixel rate).
The PLL gives the best jitter performance at high
frequencies. For this reason, in order to output low
pixel rates and still get good jitter performance, the
PLL actually operates at a higher frequency but then
divides down the clock rate afterwards. See Table 13
for the pixel rates for each VCO range setting. The
PLL output divisor is automatically selected with the
VCO range setting. The power-up default value is 01.
Table 13. VCO Ranges
VCO Range
Pixel Rates
00
10 to 21
01
21 to 42
10
42 to 84
11
84 to 95
0x03
5:3
Charge Pump Current
Three bits that establish the current driving the loop
filter in the clock generator. The current must be set to
correspond with the desired operating frequency. The
power-up default value is current = 001.
Table 14. Charge Pump Currents
Ip2
Ip1
Ip0
Current
0
50
0
1
100
0
1
0
150
0
1
250
1
0
350
1
0
1
500
1
0
750
1
1500
0x03
2
External Clock Enable
This bit determines the source of the pixel clock.
Table 15. External Clock Select Settings
EXTCLK
Function
0
Internally generated clock
1
Externally provided clock signal
A Logic 0 enables the internal PLL that generates the
pixel clock from an externally provided Hsync.
A Logic 1 enables the external EXTCLK input pin. In
this mode, the PLL Divide Ratio (PLLDIV) is ignored.
The clock phase adjust (PHASE) is still functional.
The power-up default value is EXTCLK = 0.
相關PDF資料 |
PDF描述 |
|---|---|
| V150B24H150BL | CONVERTER MOD DC/DC 24V 150W |
| SY100E445JZ TR | IC CONV 4BIT SER/PAR 28-PLCC |
| SY10E446JZ TR | IC CONV 4BIT PAR/SER 28-PLCC |
| SY10E445JZ TR | IC CONV 4BIT SER/PAR 28-PLCC |
| D38999/26FC8SN | CONN PLUG 8POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9980KSTZ-95 | 功能描述:IC INTERFACE 8BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9980KSTZ-RL95 | 制造商:Analog Devices 功能描述: |
| AD9980PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9981 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9981/PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
發布緊急采購，3分鐘左右您將得到回復。