- 您現在的位置：買賣IC網 > PDF目錄11670 > AD9974BBCZ (Analog Devices Inc)IC CCDSP DUAL 14BIT 100-CSPBGA PDF資料下載
參數資料
| 型號： | AD9974BBCZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 30/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCDSP DUAL 14BIT 100-CSPBGA |
| 標準包裝： | 1 |
| 類型： | CCD 信號處理器，14 位 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線串口 |
| 電流 - 電源： | 55mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LFBGA，CSPBGA |
| 供應商設備封裝： | 100-CSBGA（9x9） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD9974
Rev. A | Page 36 of 52
STANDBY MODE OPERATION
The AD9974 contains two standby modes to optimize the
overall power dissipation in a particular application. Bit 1 and
Bit 0 of Address 0x00 control the power-down state of the device.
STANDBY[1:0] = 00 = normal operation (full power)
STANDBY[1:0] = 01 = reference standby mode
STANDBY[1:0] = 10 or 11 = total shutdown mode
(lowest power)
Table 20 summarizes the operation of each power-down mode.
The OUT_CONTROL register takes priority over the reference
standby mode in determining the digital output states, but total
shutdown mode takes priority over OUT_CONTROL. Total
shutdown mode has the lowest power consumption.
When returning from total shutdown mode to normal operation,
the timing core must be reset at least 100 μs after the STANDBY
register is written to.
There is an additional register to disable the internal voltage
reference buffer (Address 0x00[2]) independently. By default
the buffer is disabled, but it must be enabled for normal operation.
CLI FREQUENCY CHANGE
If the input clock, CLI, is interrupted or changes to a different
frequency, the timing core must be reset for proper operation.
After the CLI clock has settled to the new frequency, or the
previous frequency has resumed, write 0 and then 1 to the
TGCORE_RST register (Address 0x14). This guarantees proper
timing core operation.
Table 20. Standby Mode Operation
I/O Block
Total Shutdown (Default)1, 2
OUT_CONTROL = Low2
Reference Standby
AFE
Off
No change
Only REFT, REFB on
Timing Core
Off
No change
On
H1
High-Z
Low
Low (4.3 mA)
H2
High-Z
High
High (4.3 mA)
H3
High-Z
Low
Low (4.3 mA)
H4
High-Z
High
High (4.3 mA)
HL
High-Z
Low
Low (4.3 mA)
RG
High-Z
Low
Low (4.3 mA)
DOUT
Low3
Low
1 To exit total shutdown, write 00 to STANDBY (Address 0x00, Bits[1:0]), then reset the timing core after 100 μs to guarantee proper settling.
2 Total shutdown mode takes priority over OUT_CONTROL for determining the output polarities.
3 The status of the DOUT pins is unknown at power-up. Low status is guaranteed in total shutdown mode after the power-up sequence is completed.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9895KBCZ | IC CCD SIGNAL PROC/GEN 64-CSPBGA |
| AD9849AKSTZ | IC CCD SIGNAL PROC 12BIT 48LQFP |
| AD9847AKSTZ | IC CCD SIGNAL PROC 10BIT 48-LQFP |
| AD9944KCPZ | IC CCD SIGNAL PROCESSOR 32-LFCSP |
| 3-221185-1 | PLUG,75 OHM,COML BNC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9974BBCZRL | 功能描述:IC CCDSP DUAL 14BIT 100-CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9975 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End |
| AD9975ABST | 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End |
| AD9975ABSTEB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End |
| AD9975ABSTRL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Broadband Modem Mixed-Signal Front End |
發布緊急采購，3分鐘左右您將得到回復。