參數資料
型號: AD9943KCPZRL
廠商: Analog Devices Inc
文件頁數: 10/20頁
文件大?。?/td> 0K
描述: IC CCD SIGNAL PROCESS 32LFCSP TR
標準包裝: 5,000
類型: CCD 信號處理器,10 位
輸入類型: 邏輯
輸出類型: 邏輯
接口: 3 線串口
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-VQ(5x5)
包裝: 帶卷 (TR)
AD9943/AD9944
Data Sheet
Figure 18. AD9944 Recommended Circuit Configuration for CCD Mode
INTERNAL POWER-ON RESET CIRCUITRY
After power-on, the AD9943/AD9944 automatically reset all
internal registers and perform internal calibration procedures.
This takes approximately 1 ms to complete. During this time,
normal clock signals and serial write operations may occur.
However, serial register writes are ignored until the internal
reset operation is completed.
GROUNDING AND DECOUPLING
RECOMMENDATIONS
As shown in Figure 17 and Figure 18, a single ground plane is
recommended for the AD9943/AD9944. This ground plane
should be as continuous as possible. This ensures that all analog
decoupling capacitors provide the lowest possible impedance
path between the power and bypass pins and their respective
ground pins. All decoupling capacitors should be located as
close as possible to the package pins. A single clean power
supply is recommended for the AD9943 and AD9944, but a
separate digital driver supply may be used for DRVDD (Pin 11).
DRVDD should always be decoupled to DRVSS (Pin 12), which
should be connected to the analog ground plane. Advantages of
using a separate digital driver supply include using a lower
voltage (2.7 V) to match levels with a 2.7 V ASIC, and reducing
digital power dissipation and potential noise coupling. If the
digital outputs must drive a load larger than 20 pF, buffering
is the recommended method to reduce digital code transition
noise. Alternatively, placing series resistors close to the digital
output pins may also help reduce noise.
Note: The exposed pad on the bottom of the AD9943/AD9944
should be soldered to the GND plane of the printed circuit board.
24
REFB
23
REFT
22
CCDIN
21
AVSS
D2
1
D3
2
D0
D1
D4
3
20
AVDD
19
SHD
18
SHP
17
CLPOB
D5
4
D6
5
D7
6
D8
7
D9
8
DATA
OUTPUTS
12
D10
D11
9
10
3V
DRIVER
SUPPLY
3V
ANALOG
SUPPLY
3V
ANALOG
SUPPLY
DRV
DD
DRV
S
DV
DD
DAT
ACL
K
D
VSS
P
BL
K
12 13 14 15 16
5
CLOCK
INPUTS
3
SERIAL
INTERFACE
CCDIN
1.0F
0.1F
NC = NO CONNECT
32 31 30 29 28 27 26 25
NC
S
CK
S
DT
A
SL
11
02905-
019
AD9944
TOP VIEW
(Not to Scale)
Rev. C | Page 18 of 20
相關PDF資料
PDF描述
MC908QT2ACPE IC MCU 8BIT 1.5K FLASH 8-DIP
D38999/20WG11PN CONN RCPT 11POS WALL MNT W/PINS
2081204-3 CONN JACK SMA BULKHEAD RG174
AD8496CRMZ-R7 THERMOCOUPLE AMPLIFIER I
VE-BNX-CU-S CONVERTER MOD DC/DC 5.2V 200W
相關代理商/技術參數
參數描述
AD9943KCPZRL1 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit and 12-Bit, 25 MHz CCD Signal Processors
AD9943-WAFER 功能描述:IC CCD SIGNAL PROCESSOR 制造商:analog devices inc. 系列:- 包裝:散裝 零件狀態:上次購買時間 類型:CCD 信號處理器,10 位 輸入類型:邏輯 輸出類型:邏輯 接口:3 線串口 電流 - 電源:- 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:模具 供應商器件封裝:模具 標準包裝:1
AD9944 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 10-Bit and 12-Bit, 25 MHz CCD Signal Processors
AD9944KCP 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 32-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:12 BIT 25 MHZ ANALOG FRONT END CONVERTER - Bulk
AD9944KCPRL 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 32-Pin LFCSP EP T/R 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel