參數資料
型號： AD9787BSVZRL
廠商： Analog Devices Inc
文件頁數： 19/64頁
文件大小： 0K
描述： IC DAC 14BIT 800MSPS 100TQFP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
標準包裝： 1,000
系列： TxDAC®
位數： 14
數據接口： 串行
轉換器數目： 2
電壓電源： 模擬和數字
功率耗散（最大）： 450mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP 裸露焊盤
供應商設備封裝： 100-TQFP-EP（14x14）
包裝： 帶卷 (TR)
輸出數目和類型： 4 電流，單極；4 電流，雙極
采樣率（每秒）： 800M
AD9785/AD9787/AD9788
Rev. A | Page 26 of 64
The digital control (DCTL) register comprises two bytes located at Address 0x01.
Table 11. Digital Control (DCTL) Register
Address
Bit
Name
Description
0x01
[15]
Reserved
Reserved for future use.
[14]
Clear phase
accumulator
0: Default. The feature that clears the NCO phase accumulator is inactive. The phase
accumulator operates as normal.
1: The NCO phase accumulator is held in the reset state until this bit is cleared.
[13]
PN code sync
enable
0: PN code synchronization mode is disabled.
1: PN code synchronization mode is enabled. See the Device Synchronization section for
details.
[12]
Sync mode select
0: Selects pulse mode synchronization.
1: Selects PN code synchronization. See the Device Synchronization section for details.
[11]
Pulse sync enable
0: Pulse mode synchronization is disabled.
1: Pulse mode synchronization is enabled. See the Device Synchronization section for details.
[10]
Reserved
Reserved for future use.
[9]
Inverse sinc
enable
0: Default. The inverse sinc filter is bypassed.
1: The inverse sinc filter is enabled and operational.
[8]
DATACLK
output enable
0: Data clock pin is disabled.
1: Default. The output data clock pin is active (configured as an output).
[7:6]
Interpolation
Factor [1:0]
Specifies the filter interpolation rate where:
00: 1× interpolation
01: 2× interpolation
10: 4× interpolation
11: 8× interpolation
[5]
Data format
0: Default. The incoming data is expected to be twos complement.
1: The incoming data is expected to be offset binary.
[4]
Single-port mode
0: Default. When the single-port bit is cleared, I/Q data is sampled simultaneously on the P1D
and P2D input ports. Specifically, I data is registered from the P1D[15:0] pins and Q data is
registered from the P2D[15:0] pins.
1: When the single-port bit is set, I/Q data is sampled in a serial word fashion on the P1D input
port. In this mode, the I/Q data is sampled into the part at twice the I/Q sample rate.
[3]
Real mode
0: Default. Logic 0 is the inactive state for this bit.
1: When the real mode bit is set, the Q path logic after modulation and phase compensation is
disabled.
[2]
IQ select invert
0: Default. When the IQ Select Invert bit is cleared, a Logic 1 on the TXENABLE pin indicates
I data, and a Logic 0 on the TXENABLE pin indicates Q data, if the user is employing a
continuous timing style on the TXENABLE pin.
1: When the IQ Select Invert bit is set, a Logic 1 on the TXENABLE pin indicates Q data, and a
Logic 0 on the TXENABLE pin indicates I data, if the user is employing a continuous timing
style on the TXENABLE pin.
[1]
Q first (data
pairing)
0: Default. When the Q first bit is cleared, the I/Q data pairing is nominal, that is, the I data
precedes the Q data in the assembly of the I/Q data pair. As such, data input to the device as
I0, Q0, I1, Q1 . . . In, Qn is paired as follows: (I0/Q0), (I1/Q1) … (In/Qn).
1: When the Q first bit is set, the I/Q data pairing is altered such that the I data is paired with
the previous Q data. As such, data input to the device as I0, Q0, I1, Q1, I2, Q2, I3, Q3 . . . In, Qn is
paired as follows: (I1/Q0), (I2/Q1), (I3/Q2) … (In + 1/Qn).
[0]
Modulator gain
control
0: Default. No gain scaling is applied to the NCO input to the internal digital modulator.
1: Gain scaling of 0.5 is applied to the NCO input to the modulator. This can eliminate
saturation of the modulator output for some combinations of data inputs and NCO signals.
相關PDF資料
PDF描述
VI-B1T-MX-S CONVERTER MOD DC/DC 6.5V 75W
VE-B1W-MX-S CONVERTER MOD DC/DC 5.5V 75W
AD7549JNZ IC DAC 12BIT LC2MOS DUAL 20DIP
AD669BR-REEL IC DAC 16BIT MONO VREF 28-SOIC
DAC8413FPC-REEL IC DAC 12BIT QUAD V-OUT 28-PLCC
相關代理商/技術參數
參數描述
AD9787-DPG2-EBZ 功能描述:BOARD EVALUATION FOR AD9787 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9787-EBZ 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk
AD9788 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual 12-/14-/16-Bit 800 MSPS DAC with Low Power 32-Bit Complex NCO
AD9788BSVZ 功能描述:IC DAC 16BIT 800MSPS 100TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF)
AD9788BSVZRL 功能描述:IC DAC 16BIT 800MSPS 100TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*