- 您現在的位置：買賣IC網 > PDF目錄375249 > AD977 (Analog Devices, Inc.) 16-Bit, 100 kSPS BiCMOS A/D Converter(100kSPS 16位A/D轉換器) PDF資料下載
參數資料
| 型號： | AD977 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 16-Bit, 100 kSPS BiCMOS A/D Converter(100kSPS 16位A/D轉換器) |
| 中文描述： | 16位，100 kSPS的BiCMOS工藝的A / D轉換器（100ksps的16位的A / D轉換器） |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 287K |
| 代理商： | AD977 |
AD977/AD977A
–7–
REV. A
DEFINITION OF SPECIFICATIONS
INTEGRAL NONLINEARITY ERROR (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as “negative full scale” occurs 1/2 LSB
before the first code transition. “Positive full scale” is defined as
a level 1 1/2 LSB beyond the last code transition. The deviation
is measured from the middle of each particular code to the true
straight line.
DIFFERENTIAL NONLINEARITY ERROR (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
FULL-SCALE ERROR
The last + transition (from 011 . . . 10 to 011 . . . 11) should
occur for an analog voltage 1 1/2 LSB below the nominal full
scale (9.9995422 V for a
±
10 V range). The full-scale error is
the deviation of the actual level of the last transition from the
ideal level.
BIPOLAR ZERO ERROR
Bipolar zero error is the difference between the ideal midscale
input voltage (0 V) and the actual voltage producing the
midscale output code.
UNIPOLAR ZERO ERROR
In unipolar mode, the first transition should occur at a level
1/2 LSB above analog ground. Unipolar zero error is the devia-
tion of the actual transition from that point.
SPURIOUS FREE DYNAMIC RANGE
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first six harmonic com-
ponents to the rms value of a full-scale input signal and is ex-
pressed in decibels.
SIGNAL TO (NOISE AND DISTORTION) (S/[N+D]) RATIO
S/(N+D) is the ratio of the rms value of the measured input
signal to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
FULL POWER BANDWIDTH
The full power bandwidth is defined as the full-scale input fre-
quency at which the S/(N+D) degrades to 60 dB, 10 bits of
accuracy.
APERTURE DELAY
Aperture delay is a measure of the acquisition performance, and
is measured from the falling edge of the R/
C
input to when the
input signal is held for a conversion.
TRANSIENT RESPONSE
The time required for the AD977/AD977A to achieve its rated
accuracy after a full-scale step function is applied to its input.
OVERVOLTAGE RECOVERY
The time required for the ADC to recover to full accuracy after
an analog input signal 150% of full-scale is reduced to 50% of
the full-scale value.
相關PDF資料 |
PDF描述 |
|---|---|
| AD977A | 16-Bit, 200 kSPS BiCMOS A/D Converter(200kSPS 16位A/D轉換器) |
| AD9803JST | CCD Signal Processor For Electronic Cameras |
| AD9804 | Complete 10-Bit 18 MSPS CCD Signal Processor |
| AD9804JST | Complete 10-Bit 18 MSPS CCD Signal Processor |
| AD9850BRS | CMOS, 125 MHz Complete DDS Synthesizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9772 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 150 MSPS TxDAC⑩ with 2x Interpolation Filter |
| AD9772A | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 160 MSPS TxDAC+ with 2x Interpolation Filter |
| AD9772AAST | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 14-bit 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:14BIT 160 MSPS TXDAC+ W/2X INTERPOLATION - Tape and Reel 制造商:Analog Devices 功能描述:Digital-Analog Converter IC Number of Bi |
| AD9772AASTRL | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 14-bit 48-Pin LQFP T/R |
| AD9772AASTZ | 功能描述:IC DAC 14BIT 160MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。