- 您現在的位置：買賣IC網 > PDF目錄1988 > AD9609BCPZRL7-80 (Analog Devices Inc)IC ADC 10BIT SRL/SPI 80M 32LFCSP PDF資料下載
參數資料
| 型號： | AD9609BCPZRL7-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SRL/SPI 80M 32LFCSP |
| 標準包裝： | 1,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 92mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9609
Rev. 0 | Page 24 of 32
BUILT-IN SELF-TEST (BIST) AND OUTPUT TEST
The AD9609 includes a built-in test feature designed to enable
verification of the integrity of each channel as well as to facili-
tate board level debugging. A built-in self-test (BIST) feature that
verifies the integrity of the digital datapath of the AD9609 is
included. Various output test options are also provided to place
predictable values on the outputs of the AD9609.
BUILT-IN SELF-TEST (BIST)
The BIST is a thorough test of the digital portion of the selected
AD9609 signal path. Perform the BIST test after a reset to ensure
that the part is in a known state. During BIST, data from an internal
pseudorandom noise (PN) source is driven through the digital
datapath of both channels, starting at the ADC block output.
At the datapath output, CRC logic calculates a signature from
the data. The BIST sequence runs for 512 cycles and then stops.
Once completed, the BIST compares the signature results with a
pre-determined value. If the signatures match, the BIST sets Bit 0
of Register 0x24, signifying the test passed. If the BIST test failed,
Bit 0 of Register 0x24 is cleared. The outputs are connected
during this test, so the PN sequence can be observed as it runs.
Writing 0x05 to Register 0x0E runs the BIST. This enables the Bit 0
(BIST enable) of Register 0x0E and resets the PN sequence
generator, Bit 2 (BIST INIT) of Register 0x0E. At the completion of
the BIST, Bit 0 of Register 0x24 is automatically cleared. The PN
sequence can be continued from its last value by writing a 0 in
Bit 2 of Register 0x0E. However, if the PN sequence is not reset,
the signature calculation does not equal the predetermined
value at the end of the test. At that point, the user needs to rely
on verifying the output data.
OUTPUT TEST MODES
The output test options are described in Table 17 at Address
0x0D. When an output test mode is enabled, the analog section
of the ADC is disconnected from the digital back-end blocks
and the test pattern is run through the output formatting block.
Some of the test patterns are subject to output formatting, and
some are not. The PN generators from the PN sequence tests
can be reset by setting Bit 4 or Bit 5 of Register 0x0D. These
tests can be performed with or without an analog signal (if
present, the analog signal is ignored), but they do require an
encode clock. For more information, see the AN-877
Application Note, Interfacing to High Speed ADCs via SPI.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9613BCPZ-170 | IC ADC 12BIT SRL 170MSPS 64LFCSP |
| AD9627ABCPZ-125 | IC ADC 12BIT 1255MSPS 64LFCSP |
| AD9627ABCPZ11-150 | IC ADC 11BIT 150MSPS 64LFCSP |
| AD9628BCPZRL7-125 | IC ADC 12BIT 125MSPS 64LFCSP |
| AD9629BCPZ-65 | IC ADC 12BIT 65MSPS 32LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9609XCPZ-40 | 功能描述:IC ADC 10BIT SPI/SRL 40M 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| AD9609XCPZ-80 | 功能描述:IC ADC 10BIT SRL/SPI 80M 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| AD9610 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Bandwidth, Fast Settling Operational Amplifier |
| AD9610/PCB | 制造商:Analog Devices 功能描述: |
| AD9610BH | 制造商:Analog Devices 功能描述:OP Amp Single GP 制造商:Rochester Electronics LLC 功能描述:AD9610 HYBRID OP AMP IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。