- 您現在的位置：買賣IC網 > PDF目錄1986 > AD9481BSUZ-250 (Analog Devices Inc)IC ADC 8BIT 250MSPS 3.3V 44-TQFP PDF資料下載
參數資料
| 型號： | AD9481BSUZ-250 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT 250MSPS 3.3V 44-TQFP |
| 標準包裝： | 1 |
| 位數： | 8 |
| 采樣率（每秒）： | 250M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 439mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-TQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個單端，單極；2 個差分，單極 |
| 產品目錄頁面： | 780 (CN2011-ZH PDF) |
| 配用： | AD9481-PCBZ-ND - BOARD EVAL 8BIT 250MSPS 44-TQFP |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD9481
Rev. 0 | Page 10 of 28
TERMINOLOGY
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the 50% point of the rising edge of the
encode command and the instant the analog input is sampled.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Clock Pulse-Width/Duty Cycle
Pulse-width high is the minimum amount of time that the clock
pulse should be left in a Logic 1 state to achieve rated
performance; pulse-width low is the minimum time clock pulse
should be left in a low state. See timing implications of changing
these specifications define an acceptable clock duty cycle.
Crosstalk
Coupling onto one channel being driven by a low level
(40 dBFS) signal when the adjacent interfering channel is
driven by a full-scale signal.
Differential Analog Input Resistance, Differential Analog
Input Capacitance, and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the
capacitance and differential input impedances are measured
with a network analyzer.
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak-to-peak differential is computed by rotating
the inputs phase 180° and taking the peak measurement again.
The difference is then computed between both peak
measurements.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Effective Number of Bits (ENOB)
ENOB is calculated from the measured SINAD based on the
equation (assuming full-scale input)
6.02
dB
1.76
=
MEASURED
SINAD
ENOB
Full-Scale Input Power
Expressed in dBm. Computed using the following equation
=
0.001
log
10
INPUT
FULLSCALE
2
FULLSCALE
Z
rms
V
Power
Gain Error
Gain error is the difference between the measured and ideal
full-scale input voltage range of the ADC.
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a best straight line
determined by a least square curve fit.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Output Propagation Delay
The delay between a differential crossing of CLK+ and CLK
and the time when all output data bits are within valid logic
levels.
Noise (for Any Range within the ADC)
This value includes both thermal and quantization noise.
×
=
10
.001
0
Z
dBFS
dBc
dBm
noise
Signal
SNR
FS
V
where:
Z
is the input impedance.
FS
is the full scale of the device for the frequency in question.
SNR
is the value for the particular input level.
Signal
is the signal level within the ADC reported in dB below
full scale.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9484BCPZRL7-500 | IC ADC 8BIT 500MSPS 56LFCSP |
| AD9510BCPZ-REEL7 | IC CLOCK DIST 8OUT PLL 64LFCSP |
| AD9511BCPZ-REEL7 | IC CLOCK DIST 5OUT PLL 48LFCSP |
| AD9512UCPZ-EP-R7 | IC CLOCK DIST 5OUT PLL 48LFCSP |
| AD9512UCPZ-EP | IC CLOCK DIST 5OUT PLL 48LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9481-PCB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 8BIT, 250 MSPS 3.3V A/D CNVRTR - Bulk |
| AD9481-PCBZ | 功能描述:BOARD EVAL 8BIT 250MSPS 44-TQFP RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9483 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Triple 8-Bit, 140 MSPS A/D Converter |
| AD9483/PCB | 制造商:Analog Devices 功能描述: |
| AD9483KS-100 | 制造商:Analog Devices 功能描述:ADC Triple Flash 100Msps 8-bit Parallel 100-Pin MQFP 制造商:Analog Devices 功能描述:ADC TRIPLE FLASH 100MSPS 8BIT PARALLEL 100MQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。