- 您現在的位置：買賣IC網 > PDF目錄373961 > AD9243EB (Analog Devices, Inc.) Complete 14-Bit, 3.0 MSPS Monolithic A/D Converter PDF資料下載
參數資料
| 型號： | AD9243EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Complete 14-Bit, 3.0 MSPS Monolithic A/D Converter |
| 中文描述： | 完整的14位，3.0 MSPS的單片機的A / D轉換器 |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 545K |
| 代理商： | AD9243EB |
AD9243
REV. A
–9–
The input SHA of the AD9243 is optimized to meet the perfor-
mance requirements for some of the most demanding commu-
nication, imaging, and data acquisition applications while
maintaining low power dissipation. Figure 22 is a graph of the
full-power bandwidth of the AD9243, typically 40 MHz. Note
that the small signal bandwidth is the same as the full-power
bandwidth. The settling time response to a full-scale stepped
input is shown in Figure 23 and is typically 80 ns to 0.0025%.
The low input referred noise of 0.36 LSB’s rms is displayed via
a grounded histogram and is shown in Figure 13.
FREQUENCY – MHz
0
–3
–12
1
100
10
A
–6
–9
Figure 22. Full-Power Bandwidth
SETTLING TIME – ns
C
16000
12000
0
0
60
10
20
30
40
50
8000
4000
70
80
Figure 23. Settling Time
The SHA’s optimum
distortion
performance for a differential or
single-ended input is achieved under the following two condi-
tions: (1) the common-mode voltage is centered around mid
supply (i.e., AVDD/2 or approximately 2.5 V) and (2) the input
signal voltage span of the SHA is set at its lowest (i.e., 2 V input
span). This is due to the sampling switches, Q
S1
, being CMOS
switches whose R
ON
resistance is very low but has some signal
dependency which causes frequency dependent ac distortion
while the SHA is in the track mode. The R
ON
resistance of a
CMOS switch is typically lowest at its midsupply but increases
symmetrically as the input signal approaches either AVDD or
AVSS. A lower input signal voltage span centered at midsupply
reduces the degree of R
ON
modulation.
Figure 24 compares the AD9243’s THD vs. frequency perfor-
mance for a 2 V input span with a common-mode voltage of
1 V and 2.5 V. Note the difference in the amount of degrada-
tion in THD performance as the input frequency increases.
Similarly, note how the THD performance at lower frequencies
becomes less sensitive to the common-mode voltage. As the
input frequency approaches dc, the distortion will be domi-
nated by static nonlinearities such as INL and DNL. It is
important to note that these dc static nonlinearities are inde-
pendent of any R
ON
modulation.
FREQUENCY – MHz
T
–50
–60
–90
0.1
1
10
–70
–80
V
CM
= 1.0V
V
CM
= 2.5V
Figure 24. AD9243 THD vs. Frequency for V
CM
= 2.5 V and
1.0 V (A
IN
= –0.5 dB, Input Span = 2.0 V p-p)
Due to the high degree of symmetry within the SHA topology, a
significant improvement in distortion performance for differen-
tial input signals with frequencies up to and beyond Nyquist can
be realized. This inherent symmetry provides excellent cancella-
tion of both common-mode distortion and noise. Also, the
required input signal voltage span is reduced by a half which
further reduces the degree of R
ON
modulation and its effects on
distortion.
The optimum
noise and dc linearity
performance for either
differential or single-ended inputs is achieved with the largest
input signal voltage span (i.e., 5 V input span) and matched
input impedance for VINA and VINB. Note that only a slight
degradation in dc linearity performance exists between the
2 V and 5 V input span as specified in the AD9243 “DC
SPECIFICATIONS.”
Referring to Figure 21, the differential SHA is implemented
using a switched-capacitor topology. Hence, its input imped-
ance and its subsequent effects on the input drive source should
be understood to maximize the converter’s performance. The
combination of the pin capacitance, C
PIN
, parasitic capacitance
C
PAR,
and the sampling capacitance, C
S
, is typically less than
16 pF. When the SHA goes into track mode, the input source
must charge or discharge the voltage stored on C
S
to the new
input voltage. This action of charging and discharging C
S
which
is approximately 4 pF, averaged over a period of time and for a
given sampling frequency, F
S
, makes the input impedance ap-
pear to have a benign resistive component (i.e., 83 k
at F
S
=
3.0 MSPS). However, if this action is analyzed within a sam-
pling period (i.e., T = <1/F
S
), the input impedance is dynamic
due to the instantaneous requirement of charging and discharg-
ing C
S
. A series resistor inserted between the input drive source
and the SHA input as shown in Figure 25 provides the effective
isolation.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9243* | 14-Bit Rail-to-Rail DACs with I2C Interface; Package: DFN; No of Pins: 10; Temperature Range: 0°C to +70°C |
| AD9244 | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9244-40PCB | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9244-65PCB | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9244BSTRL-40 | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9243-EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD9243 制造商:Analog Devices 功能描述:DEV TOOLS, EVAL BD FOR AD9243 - Bulk |
| AD9244 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9244_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 40 MSPS/65 MSPS A/D Converter |
| AD9244-40PCB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD9244 ,14BIT, 40/65MSPS A/D CNVRTR - Bulk |
| AD9244-40PCBZ | 制造商:Analog Devices 功能描述:Evaluation Board For Ad9244-40 制造商:Analog Devices 功能描述:14 BIT 40/65 MSPS IF SAMPLING ADC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。