參數資料
型號: AD9219ABCPZRL7-40
廠商: Analog Devices Inc
文件頁數: 22/56頁
文件大?。?/td> 0K
描述: IC ADC 10BIT SRL 40MSPS 64LFCSP
標準包裝: 750
位數: 10
采樣率(每秒): 40M
數據接口: 串行,SPI?
轉換器數目: 4
功率耗散(最大): 313mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-VFQFN 裸露焊盤,CSP
供應商設備封裝: 48-LFCSP-VQ(7x7)
包裝: 帶卷 (TR)
輸入數目和類型: 8 個單端,單極;4 個差分,單極
Data Sheet
AD9219
Rev. E | Page 29 of 56
SCLK/DTP Pin
The SCLK/DTP pin is for use in applications that do not require
SPI mode operation. This pin can enable a single digital test
pattern if it and the CSB pin are held high during device power-
up. When SCLK/DTP is tied to AVDD, the ADC channel
outputs shift out the following pattern: 1000 0000 0000. The
FCO and DCO function normally while all channels shift out the
repeatable test pattern. This pattern allows the user to perform
timing alignment adjustments among the FCO, DCO, and output
data. For normal operation, this pin should be tied to AGND
through a 10 kΩ resistor. This pin is both 1.8 V and 3.3 V tolerant.
Table 12. Digital Test Pattern Pin Settings
Selected DTP
DTP Voltage
Resulting
D + x and D x
Resulting
FCO and DCO
Normal
Operation
10 kΩ to AGND
Normal
operation
Normal operation
DTP
AVDD
1000 0000 0000
Normal operation
Additional and custom test patterns can also be observed when
commanded from the SPI port. Consult the Memory Map
section for information about the options available.
CSB Pin
The CSB pin should be tied to AVDD for applications that do
not require SPI mode operation. By tying CSB high, all SCLK
and SDIO information is ignored. This pin is both 1.8 V and
3.3 V tolerant.
RBIAS Pin
To set the internal core bias current of the ADC, place a resistor
(nominally equal to 10.0 kΩ) to ground at the RBIAS pin. The
resistor current is derived on-chip and sets the AVDD current
of the ADC to a nominal 232 mA at 65 MSPS. Therefore, it is
imperative that at least a 1% tolerance on this resistor be used to
achieve consistent performance.
Voltage Reference
A stable, accurate 0.5 V voltage reference is built into the
AD9219. This is gained up internally by a factor of 2, setting
VREF to 1.0 V, which results in a full-scale differential input span
of 2 V p-p. The VREF is set internally by default; however, the
VREF pin can be driven externally with a 1.0 V reference to
improve accuracy.
When applying the decoupling capacitors to the VREF, REFT,
and REFB pins, use ceramic low ESR capacitors. These capacitors
should be close to the ADC pins and on the same layer of the
PCB as the AD9219. The recommended capacitor values and
configurations for the AD9219 reference pin are shown in
Table 13. Reference Settings
Selected Mode
SENSE Voltage
Resulting VREF (V)
Resulting
Differential
Span (V p-p)
External
Reference
AVDD
N/A
2 × external
reference
Internal,
2 V p-p FSR
AGND to 0.2 V
1.0
2.0
相關PDF資料
PDF描述
AD7893BRZ-2REEL IC ADC 12BIT SRL T/H LP 8SOIC
VI-B4X-IV-S CONVERTER MOD DC/DC 5.2V 150W
VE-272-MY CONVERTER MOD DC/DC 15V 50W
MS27473T20B41PD CONN PLUG 41POS STRAIGHT W/PINS
EN3C9F26SX CONN PLUG 9POS FEMALE CORD #26
相關代理商/技術參數
參數描述
AD9219ABCPZRL7-65 功能描述:IC ADC 10BIT SRL 65MSPS 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD9219BCPZ-40 制造商:Analog Devices 功能描述:ADC Quad Pipelined 40Msps 10-bit Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC 10BIT ADC QUAD 40MSPS LFCSP48
AD9219BCPZ-65 制造商:Analog Devices 功能描述:ADC Quad Pipelined 65Msps 10-bit Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC 10BIT ADC QUAD 65MSPS LFCSP48
AD9219BCPZRL-40 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter
AD9219BCPZRL-65 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad, 10-Bit, 40/65 MSPS Serial LVDS 1.8 V A/D Converter