- 您現在的位置：買賣IC網 > PDF目錄10540 > AD9051BRSZ-2V (Analog Devices Inc)IC ADC 10BIT 60MSPS 28-SSOP PDF資料下載
參數資料
| 型號： | AD9051BRSZ-2V |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 60MSPS 28-SSOP |
| 標準包裝： | 47 |
| 位數： | 10 |
| 采樣率（每秒）： | 60M |
| 數據接口： | 并聯 |
| 轉換器數目： | 3 |
| 功率耗散（最大）： | 315mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
REV.
AD9051
–10–
Overdrive of the Analog Input
Special care was taken in the design of the analog input section
of the AD9051 to prevent damage and corruption of data when
the input is overdriven. The nominal input range is 1.875 V to
3.125 V (1.25 V p-p centered at 2.5 V). Out-of-range compara-
tors detect when the analog input signal is out of this range and
the input buffer is clamped. The digital outputs are locked at
their maximum or minimum value (i.e., all “0” or all “1”). This
precludes the digital outputs changing to an invalid value when
the analog input is out of range.
The input is protected to one volt outside the power supply
rails. For nominal power (5 V and ground), the analog input
will not be damaged with signals from +5.5 V to –0.5 V.
Timing
The performance of the AD9051 is very insensitive to the duty
cycle of the clock. Pulsewidth variations of as much as
±15% for
encode rates of 40 MSPS and
±10% for encode rates of 60 MSPS
will cause no degradation in performance. (See Figure 17, SNR vs.
Duty Cycle.)
The AD9051 provides latched data outputs, with five pipeline
delays. Data outputs are available one propagation delay (tPD)
after the rising edge of the encode command (refer to Figure 1,
Timing Diagram). The length of the output data lines and
loads placed on them should be minimized to reduce tran-
sients within the AD9051; these transients can detract from
the converter’s dynamic performance.
Power Dissipation
The power dissipation specification in the parameter table is
measured under the following conditions: encode is 60 MSPS,
analog input is –FS.
As shown in Figure 3, the actual power dissipation varies based
on these conditions. For instance, reducing the clock rate will
reduce power as expected for CMOS-type devices. The loading
determines the power dissipated in the output stages.
The analog input frequency and amplitude in conjunction with
the clock rate determine the switching rate of the output data
bits. Power dissipation increases as more data bits switch at
faster rates. For instance, if the input is a dc signal that is out of
range, no output bits will switch. This minimizes power in the
output stages, but is not realistic from a usage standpoint.
The dissipation in the output stages can be minimized by inter-
facing the outputs to 3 V logic (refer to Using the AD9051, 3 V
System). The lower output swings minimize power consumption
as follows: (1/2 CLOAD
× V
DD
2
× Update Rate).
Voltage Reference
A stable and accurate 2.5 V voltage reference is built into the
AD9051 (Pin 3, VREFOUT). In normal operation the internal
reference is used by strapping together Pins 3 and 4 of the
AD9051. The internal reference has 500
A of extra drive cur-
rent that can be used for other circuits.
Some applications may require greater accuracy, improved
temperature performance, or adjustment of the gain of the
AD9051, which cannot be obtained by using the internal refer-
ence. For these applications, an external 2.5 V reference can be
used to connect to Pin 4 of the AD9051. The VREFIN requires
2
A of drive current.
The input range can be adjusted by varying the reference
voltage applied to the AD9051. No appreciable degradation
in performance occurs when the reference is adjusted
± 5%.
The full-scale range of the ADC tracks reference voltage
changes linearly.
C
相關PDF資料 |
PDF描述 |
|---|---|
| PT07A-12-10P | CONN RCPT 10 POS JAM NUT W/PINS |
| VE-J5N-MW-F1 | CONVERTER MOD DC/DC 18.5V 100W |
| ISL3293EFHZ-T7A | IC TXRX |
| LTC1408IUH-12#PBF | IC ADC 12BIT 600KSPS 32-QFN |
| 97-3106A-18-10S | CONN PLUG 4POS W/SOCKETS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9051BRSZRL | 功能描述:IC ADC 10BIT 60MSPS 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD9051BRSZRL-2V | 功能描述:IC ADC 10BIT 60MSPS 28-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD9051PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 60 MSPS A/D Converter |
| AD9054 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 200 MSPS A/D Converter |
| AD9054/PCB | 制造商:Analog Devices 功能描述:TEST BOARD AD9054 |
發布緊急采購，3分鐘左右您將得到回復。