- 您現在的位置：買賣IC網 > PDF目錄5250 > AD8572AR-REEL (Analog Devices Inc)IC OPAMP CHOPPER R-R DUAL 8SOIC PDF資料下載
參數資料
| 型號： | AD8572AR-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP CHOPPER R-R DUAL 8SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 斷路器（零漂移） |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.4 V/µs |
| 增益帶寬積： | 1.5MHz |
| 電流 - 輸入偏壓： | 10pA |
| 電壓 - 輸入偏移： | 1µV |
| 電流 - 電源： | 850µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
AD8571/AD8572/AD8574
Rev. E | Page 20 of 24
APPLICATIONS INFORMATION
5 V PRECISION STRAIN GAGE CIRCUIT
The extremely low offset voltage of the AD8572 makes it an ideal
amplifier for any application requiring accuracy with high gains,
such as a weigh scale or strain gage. Figure 63 shows a configura-
tion for a single-supply, precision strain gage measurement system.
The REF192 provides a 2.5 V precision reference voltage for A2.
The A2 amplifier boosts this voltage to provide a 4.0 V reference
for the top of the strain gage resistor bridge. Q1 provides the
current drive for the 350 Ω bridge network. A1 is used to amplify
the output of the bridge with the full-scale output voltage equal to
(
)
B
R
2
R
1
R +
×
2
(17)
where RB is the resistance of the load cell.
Using the values given in Figure 63, the output voltage linearly
varies from 0 V with no strain to 4 V under full strain.
VOUT
AD8572-A
R3
17.4k
R4
100
R1
17.4k
R2
100
0V TO 4V
NOTE:
USE 0.1% TOLERANCE RESISTORS.
20k
A1
AD8572-B
REF192
12k
1k
5V
2.5V
6
4
3
2
4.0V
40mV
FULL-SCALE
A2
350
LOAD
CELL
Q1
2N2222
OR
EQUIVALENT
01
10
4-
06
3
Figure 63. 5 V Precision Strain Gage Amplifier
3 V INSTRUMENTATION AMPLIFIER
The high common-mode rejection, high open-loop gain,
and operation down to 3 V of the supply voltage make the
AD857x family an excellent op amp choice for discrete single-
supply instrumentation amplifiers. The common-mode
rejection ratio of the AD857x is greater than 120 dB, but the
CMRR of the system is also a function of the external resistor
tolerances. The gain of the difference amplifier shown in Figure 64
is given as
+
+
=
1
R
2
R
2
V
2
R
1
R
4
R
3
R
4
R
1
V
OUT
1
(18)
V2
V1
VOUT
R1
R3
R4
R3
R2
AD8571/
AD8572/
AD8574
IF
=
, THEN VOUT =
(V1 – V2)
01
10
4-
0
64
Figure 64. Using the AD857x as a Difference Amplifier
In an ideal difference amplifier, the ratio of the resistors is set
equal to
3
R
4
R
1
R
2
R
A
V
=
(19)
Set the output voltage of the system to
VOUT = AV (V1 V2)
(20)
Due to finite component tolerance, the ratio between the four
resistors is not exactly equal, and any mismatch results in a
reduction of common-mode rejection from the system. Referring
to Figure 64, the exact common-mode rejection ratio can be
expressed as
R2R3
R1R4
R2R3
R2R4
1R4
R
CMRR
2
+
=
(21)
In the 3-op amp instrumentation amplifier configuration shown
in Figure 65, the output difference amplifier is set to unity gain
with all four resistors equal in value. If the tolerance of the
resistors used in the circuit is given as δ, the worst-case CMRR
of the instrumentation amplifier is
δ
=
2
1
MIN
CMRR
(22)
VOUT
R
AD8574-C
V2
R
V1
RG
AD8574-B
AD8574-A
RTRIM
VOUT = 1 +
2R
RG
(V1 – V2)
01
10
4-
0
65
Figure 65. Discrete Instrumentation Amplifier Configuration
Therefore, using 1% tolerance resistors results in a worst-case
system CMRR of 0.02, or 34 dB. To achieve high common-
mode rejection, either high precision resistors or an additional
trimming resistor, as shown in Figure 65, should be used. The
value of this trimming resistor should be equal to the value of
multiplied by its tolerance. For example, using 10 kΩ resistors
with 1% tolerance would require a series trimming resistor
equal to 100 Ω.
R
相關PDF資料 |
PDF描述 |
|---|---|
| 8-1879213-5 | RES 226 OHM 1/16W 0.1% 0402 |
| MCP6001RT-I/OT | IC OPAMP SGL 1.8V R-R SOT23-5 |
| ADA4897-1ARZ-R7 | IC OPAMP GP RR 230MHZ LN 8SOIC |
| 8-1879213-4 | RES 221 OHM 1/16W 0.1% 0402 |
| LVK24R050DER | RES .05 OHM 1W .5% 2412 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8572AR-REEL7 | 功能描述:IC OPAMP CHOPPER R-R DUAL 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| AD8572ARU | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Dual R-R I/O 5V 8-Pin TSSOP Tube 制造商:Rochester Electronics LLC 功能描述:DUAL PRECISION RAIL-RAIL CHOPPER OPAMP - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP DUAL R/R |
| AD8572ARU-REEL | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Dual R-R I/O 5V 8-Pin TSSOP T/R |
| AD8572ARUZ | 功能描述:IC OPAMP CHOPPER R-R DUAL 8TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| AD8572ARUZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Single-Supply, Rail-to-Rail Input/Output Operational Amplifiers |
發(fā)布緊急采購，3分鐘左右您將得到回復。