- 您現在的位置：買賣IC網 > PDF目錄6034 > AD8555ARZ (Analog Devices Inc)IC AMP CHOPPER 2MHZ 10MA 8SOIC PDF資料下載
參數資料
| 型號： | AD8555ARZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CHOPPER 2MHZ 10MA 8SOIC |
| 標準包裝： | 98 |
| 系列： | DigiTrim® |
| 放大器類型： | 斷路器（零漂移） |
| 電路數： | 1 |
| 轉換速率： | 1.2 V/µs |
| 增益帶寬積： | 2MHz |
| 電流 - 輸入偏壓： | 16nA |
| 電壓 - 輸入偏移： | 2µV |
| 電流 - 電源： | 2mA |
| 電流 - 輸出 / 通道： | 10mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 產品目錄頁面： | 771 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD8555
Rev. A | Page 17 of 28
THEORY OF OPERATION
A1, A2, R1, R2, R3, P1, and P2 form the first gain stage of the
differential amplifier. A1 and A2 are auto-zeroed op amps that
minimize input offset errors. P1 and P2 are digital potentiome-
ters, guaranteed to be monotonic. Programming P1 and P2
allows the first stage gain to be varied from 4.0 to 6.4 with 7-bit
resolution (see Table 6 and Equation 3), giving a fine gain
adjustment resolution of 0.37%. R1, R2, R3, P1, and P2 each
have a similar temperature coefficient, so the first stage gain
temperature coefficient is lower than 100 ppm/°C.
A3, R4, R5, R6, R7, P3, and P4 form the second gain stage of the
differential amplifier. A3 is also an auto-zeroed op amp that
minimize input offset errors. P3 and P4 are digital potentiome-
ters, allowing the second stage gain to be varied from 17.5 to
200 in eight steps (see Table 7); they allow the gain to be varied
over a wide range. R4, R5, R6, R7, P3, and P4 each have a simi-
lar temperature coefficient, so the second stage gain tempera-
ture coefficient is lower than 100 ppm/°C.
RF together with an external capacitor connected between
FILT/DIGOUT and VSS or VDD form a low-pass filter. The
filtered signal is buffered by A4 to give a low impedance output
at VOUT. RF is nominally 16 kΩ, allowing a 1 kHz low-pass
filter to be implemented by connecting a 10 nF external
capacitor between FILT/DIGOUT and VSS or between
FILT/DIGOUT and VDD. If low-pass filtering is not needed,
then the FILT/DIGOUT pin must be left floating.
A5 implements a voltage buffer, which provides the positive
supply to the amplifier output buffer A4. Its function is to limit
VOUT to a maximum value, useful for driving analog-to-digital
converters (ADC) operating on supply voltages lower than
VDD. The input to A5, VCLAMP, has a very high input resis-
tance. It should be connected to a known voltage and not left
floating. However, the high input impedance allows the clamp
voltage to be set using a high impedance source, e.g., a potential
divider. If the maximum value of VOUT does not need to be
limited, VCLAMP should be connected to VDD.
A4 implements a rail-to-rail input and output unity-gain vol-
tage buffer. The output stage of A4 is supplied from a buffered
version of VCLAMP instead of VDD, allowing the positive
swing to be limited. The maximum output current is limited
between 5 mA to 10 mA.
An 8-bit digital-to-analog converter (DAC) is used to generate a
variable offset for the amplifier output. This DAC is guaranteed
to be monotonic. To preserve the ratiometric nature of the input
signal, the DAC references are driven from VSS and VDD, and
the DAC output can swing from VSS (Code 0) to VDD (Code
255). The 8-bit resolution is equivalent to 0.39% of the differ-
ence between VDD and VSS, e.g., 19.5 mV with a 5 V supply.
The DAC output voltage (VDAC) is given approximately by
() VSS
VSS
VDD
Code
VDAC
+
+
≈
256
5
.
0
(1)
The temperature coefficient of VDAC is lower than
200 ppm/°C.
The amplifier output voltage (VOUT) is given by
(
) VDAC
VNEG
VPOS
GAIN
VOUT
+
=
(2)
where GAIN is the product of the first and second stage gains.
A3
A2
A4
A5
VDD
DAC
VSS
VDD
VSS
VDD
VSS
VCLAMP
VPOS
VSS
FILT/
DIGOUT
VOUT
A1
VDD
VSS
VNEG
R1
R3
R2
R5
R7
P4
R4
R6
RF
P3
P2
P1
04598-0-001
Figure 49. AD8555 Functional Schematic
相關PDF資料 |
PDF描述 |
|---|---|
| LTC6254CMS#PBF | IC OPAMP R-R 720MHZ MSOP-16 |
| FG-8 | FINGER GUARD FOR FAN |
| TSW-126-14-T-S | CONN HEADER 26POS .100" SNGL TIN |
| TSW-126-08-T-S | CONN HEADER 26POS .100" SNGL TIN |
| TSW-107-08-T-D-RA | CONN HEADER 14PS .100 DL R/A TIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8555ARZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Digitally Programmable Sensor Signal Amplifier |
| AD8555ARZ-REEL | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源，單路/雙路(±):2 V ~ 44 V，±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP（5x3） 包裝:管件 |
| AD8555ARZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Digitally Programmable Sensor Signal Amplifier |
| AD8555ARZ-REEL7 | 功能描述:IC AMP CHOPPER 2MHZ 10MA 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:DigiTrim® 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8555ARZ-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Zero-Drift, Digitally Programmable Sensor Signal Amplifier |
發布緊急采購，3分鐘左右您將得到回復。