- 您現在的位置：買賣IC網 > PDF目錄5353 > AD8205YRZ-R7 (Analog Devices Inc)IC AMP DIFF 8SOIC PDF資料下載
參數資料
| 型號： | AD8205YRZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP DIFF 8SOIC |
| 產品培訓模塊： | Current Sense Amplifiers |
| 標準包裝： | 1,000 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 0.5 V/µs |
| -3db帶寬： | 50kHz |
| 電壓 - 輸入偏移： | 2000µV |
| 電流 - 電源： | 2mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
Data Sheet
AD8205
Rev.
| Page 11 of 12
APPLICATIONS INFORMATION
A typical application for the AD8205 is high-side measurement
of a current through a solenoid for PWM control of the
solenoid opening. Typical applications include hydraulic
transmission control and diesel injection control.
Two typical circuit configurations are used for this type of
application.
HIGH-SIDE CURRENT SENSE WITH A LOW-SIDE
SWITCH
In this case, the PWM control switch is ground referenced. An
inductive load (solenoid) is tied to a power supply. A resistive
shunt is placed between the switch and the load (see Figure 19).
An advantage of placing the shunt on the high side is that the
entire current, including the re-circulation current, can be
measured since the shunt remains in the loop when the switch
is off. In addition, diagnostics can be enhanced because shorts
to ground can be detected with the shunt on the high side.
In this circuit configuration, when the switch is closed, the
common-mode voltage moves down to near the negative rail.
When the switch is opened, the voltage reversal across the
inductive load causes the common-mode voltage to be held one
diode drop above the battery by the clamp diode.
04315-0-018
+IN VREF1 +VS OUT
–IN
GND VREF2 NC
INDUCTIVE
LOAD
AD8205
CLAMP
DIODE
42V
BATTERY
SHUNT
SWITCH
NC = NO CONNECT
5V
Figure 19. Low-Side Switch
HIGH-SIDE CURRENT SENSE WITH A HIGH-SIDE
SWITCH
This configuration minimizes the possibility of unexpected
solenoid activation and excessive corrosion (see Figure 20). In
this case, both the switch and the shunt are on the high side.
When the switch is off, this removes the battery from the load,
which prevents damage from potential shorts to ground, while
still allowing the recirculating current to be measured and
providing for diagnostics. Removing the power supply from the
load for the majority of the time minimizes the corrosive effects
that could be caused by the differential voltage between the load
and ground.
When using a high-side switch, the battery voltage is connected
to the load when the switch is closed, causing the common-
mode voltage to increase to the battery voltage. In this case,
when the switch is opened, the voltage reversal across the
inductive load causes the common-mode voltage to be held one
diode drop below ground by the clamp diode.
04315-0-019
+IN VREF1 +VS OUT
–IN
GND VREF2 NC
INDUCTIVE
LOAD
AD8205
CLAMP
DIODE
42V
BATTERY
SHUNT
SWITCH
NC = NO CONNECT
5V
Figure 20. High-Side Switch
Another typical application for the AD8205 is as part of the
control loop in H-bridge motor control. In this case, the
AD8205 is placed in the middle of the H-bridge (see Figure 21)
so that it can accurately measure current in both directions by
using the shunt available at the motor. This is a better solution
than a ground referenced op amp because ground is not
typically a stable reference voltage in this type of application.
This instability in the ground reference causes the
measurements that could be made with a simple ground
referenced op amp to be inaccurate.
The AD8205 measures current in both directions as the
H-bridge switches and the motor changes direction. The output
of the AD8205 is configured in an external reference
bidirectional mode, see the Output Offset Adjustment section.
04315-0-020
+IN VREF1 +VS OUT
–IN
GND VREF2 NC
AD8205
SHUNT
5V
2.5V
5V
CONTROLLER
NC = NO CONNECT
MOTOR
Figure 21. Motor Control Application
D
相關PDF資料 |
PDF描述 |
|---|---|
| MME23-0141C1 | CONN RACK/PANEL 14POS 5A |
| RT2010BKC07249RL | RES 249 OHM 1/2W .1% 2010 SMD |
| LM258DR2 | IC OPAMP DUAL LOW POWER 8SOIC |
| LM224DR2 | IC OPAMP QUAD LOW POWER 14SOIC |
| AD8007ARZ-R7 | IC OPAMP CF ULDIST LN LP 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8205YRZ-RL | 功能描述:IC AMP DIFF 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8206 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply, 42 V System Difference Amplifier |
| AD8206_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply, 42 V System Difference Amplifier |
| AD8206_12 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Common-Mode Voltage, Bidirectional Current Shunt Amplifier |
| AD8206AR | 制造商:Analog Devices 功能描述:SINGLE SUPPLY 42V SYSTEM DIFFERENCE AMPLIFIER - Bulk |
發布緊急采購，3分鐘左右您將得到回復。