參數資料
| 型號： | AD8203YRMZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF 60KHZ 8MSOP |
| 標準包裝： | 1,000 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 0.330 V/µs |
| 增益帶寬積： | 60kHz |
| 電流 - 輸入偏壓： | 40nA |
| 電壓 - 輸入偏移： | 2000µV |
| 電流 - 電源： | 250µA |
| 電壓 - 電源，單路/雙路(±)： | 3.5 V ~ 12 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
Data Sheet
AD8203
Rev. D | Page 15 of 20
GAIN TRIM
Figure 45 shows a method for incremental gain trimming by
using a trim potentiometer and external resistor REXT.
The following approximation is useful for small gain ranges:
ΔG ≈ (10 M/REXT)%
Thus, the adjustment range is ±2% for REXT = 5 M; ±10% for
REXT = 1 M, and so on.
5V
OUT
REXT
GAIN TRIM
20k
MIN
VCM
VDIFF
2
VDIFF
2
NC = NO CONNECT
GND
NC
–IN
+IN
A1
+VS
A2
OUT
AD8203
05013-018
Figure 45. Incremental Gain Trim
Internal Signal Overload Considerations
When configuring gain for values other than 14, the maximum
input voltage with respect to the supply voltage and ground
must be considered, since either the preamplifier or the output
buffer reaches its full-scale output (approximately VS 0.2 V)
with large differential input voltages. The input of the AD8203
is limited to (VS 0.2)/7 for overall gains ≤ 7, since the pre-
amplifier, with its fixed gain of ×7, reaches its full-scale output
before the output buffer. For gains greater than 7, the swing at
the buffer output reaches its full scale first and limits the
LOW-PASS FILTERING
In many transducer applications, it is necessary to filter the
signal to remove spurious high frequency components, includ-
ing noise, or to extract the mean value of a fluctuating signal
with a peak-to-average ratio (PAR) greater than unity. For
example, a full-wave rectified sinusoid has a PAR of 1.57, a
raised cosine has a PAR of 2, and a half-wave sinusoid has a
PAR of 3.14. Signals having large spikes can have PARs of
10 or more.
When implementing a filter, the PAR should be considered so
that the output of the AD8203 preamplifier (A1) does not clip
before A2, since this nonlinearity would be averaged and appear
as an error at the output. To avoid this error, both amplifiers
should be made to clip at the same time. This condition is
achieved when the PAR is no greater than the gain of the sec-
ond amplifier (2 for the default configuration). For example, if a
PAR of 5 is expected, the gain of A2 should be increased to 5.
Low-pass filters can be implemented in several ways by using
the features provided by the AD8203. In the simplest case, a
single-pole filter (20 dB/decade) is formed when the output of
A1 is connected to the input of A2 via the internal 100 k
resistor by strapping Pin 3, Pin 4, and a capacitor added from
this node to ground, as shown in Figure 46. If a resistor is added
across the capacitor to lower the gain, the corner frequency
increases; it should be calculated using the parallel sum of the
resistor and 100 k.
5V
VCM
VDIFF
2
VDIFF
2
NC = NO CONNECT
C
GND
NC
–IN
+IN
A1
+VS
A2
OUT
AD8203
05013-019
OUTPUT
fC =
1
2
πC105
C IN FARADS
Figure 46. Single-Pole, Low-Pass Filter Using the Internal 100 k Resistor
If the gain is raised using a resistor, as shown in Figure 44, the
corner frequency is lowered by the same factor as the gain is
raised. Thus, using a resistor of 200 k (for which the gain
would be doubled), the corner frequency is now 0.796 Hz F
(0.039 F for a 20 Hz corner frequency).
5V
VCM
VDIFF
2
VDIFF
2
NC = NO CONNECT
C
GND
NC
–IN
+IN
A1
+VS
A2
OUT
AD8203
005013-020
OUT
C
255k
fC(Hz) = 1/C(F)
Figure 47. 2-Pole, Low-Pass Filter
A 2-pole filter (with a roll-off of 40 dB/decade) can be implemented
using the connections shown in Figure 47. This is a Sallen-Key
form based on a ×2 amplifier. It is useful to remember that a 2-pole
filter with a corner frequency f2 and a 1-pole filter with a corner at f1
have the same attenuation at the frequency (f22/f1). The attenuation
Using the standard resistor value shown and equal capacitors (see
Figure 47), the corner frequency is conveniently scaled at 1 Hz F
(0.05 F for a 20 Hz corner). A maximally flat response occurs
when the resistor is lowered to 196 k and the scaling is then
1.145 Hz F. The output offset is raised by approximately 5 mV
(equivalent to 250 V at the input pins).
相關PDF資料 |
PDF描述 |
|---|---|
| KTR10EZPF4704 | RES 4.70M OHM 1/8W 1% 0805 SMD |
| 0034.5620.22 | FUSE 2A 250V TLAG 5X20 SMD T/R |
| ADA4310-1ACPZ-R2 | IC OPAMP CF DUAL LDIST 16LFCSP |
| 0034.5618.22 | FUSE 1.25A 250V TLAG 5X20SMD TR |
| KTR10EZPF1603 | RES 160K OHM 1/8W 1% 0805 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8203YRMZ-RL | 功能描述:IC AMP DIFF 60KHZ 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8203YRZ | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8203YRZ-R7 | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8203YRZ-RL | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8205 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply 42 V System Difference Amplifier |
發(fā)布緊急采購，3分鐘左右您將得到回復。