- 您現在的位置：買賣IC網 > PDF目錄5369 > AD8203YRMZ-R7 (Analog Devices Inc)IC AMP DIFF 60KHZ 8MSOP PDF資料下載
參數資料
| 型號： | AD8203YRMZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP DIFF 60KHZ 8MSOP |
| 標準包裝： | 1,000 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 0.330 V/µs |
| 增益帶寬積： | 60kHz |
| 電流 - 輸入偏壓： | 40nA |
| 電壓 - 輸入偏移： | 2000µV |
| 電流 - 電源： | 250µA |
| 電壓 - 電源，單路/雙路(±)： | 3.5 V ~ 12 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
AD8203
Data Sheet
Rev. D | Page 12 of 20
THEORY OF OPERATION
The AD8203 consists of a preamp and buffer, arranged as
shown in Figure 40. Like-named resistors have equal values.
The preamp incorporates a dynamic bridge (subtractor) circuit.
Identical networks (within the shaded areas) consisting of RA,
RB, RC, and RG, attenuate input signals applied to Pin 1 and
Pin 8. Note that when equal amplitude signals are asserted at
Input 1 and Input 8, and the output of A1 is equal to the
common potential (that is, 0), the two attenuators form a
balanced-bridge network. When the bridge is balanced, the
differential input voltage at A1, and thus its output, is 0.
Any common-mode voltage applied to both inputs keeps the
bridge balanced and the A1 output at 0. Because the resistor
networks are carefully matched, the common-mode signal
rejection approaches this ideal state.
However, if the signals applied to the inputs differ, the result is a
difference at the input to A1. A1 responds by adjusting its output
to drive RB, by way of RG, to adjust the voltage at its inverting
input until it matches the voltage at its noninverting input.
By attenuating voltages at Pin 1 and Pin 8, the amplifier inputs
are held within the power supply range, even if Pin 1 and Pin 8
input levels exceed the supply or fall below common (ground).
The input network also attenuates normal (differential) mode
voltages. RC and RG form an attenuator that scales A1 feedback,
forcing large output signals to balance relatively small differen-
tial inputs. The resistor ratios establish the preamp gain at 7.
Because the differential input signal is attenuated and then
amplified to yield an overall gain of 7, Amplifier A1 operates at
a higher noise gain, multiplying deficiencies such as input offset
voltage and noise with respect to Pin 1 and Pin 8.
A1
A3
RCM
(TRIMMED)
100k
RA
–IN
RG
RC
RB
RA
RC
RB
RG
+IN
COM
A2
RF
AD8203
5
4
3
1
2
8
05013-014
Figure 40. Simplified Schematic
To minimize these errors while extending the common-mode
range, a dedicated feedback loop is used to reduce the range of
common-mode voltage applied to A1 for a given overall range
at the inputs. By offsetting the range of voltage applied to the
compensator, the input common-mode range is also offset to
include voltages more negative than the power supply. The
A3 amplifier detects the common-mode signal applied to A1
and adjusts the voltage on the matched RCM resistors to reduce
the common-mode voltage range at the A1 inputs. By adjusting
the common voltage of these resistors, the common-mode input
range is extended while, at the same time, the normal mode
signal attenuation is reduced, leading to better performance
referred to input.
The output of the dynamic bridge taken from A1 is connected
to Pin 3 by way of a 100 k series resistor, provided for low-
pass filtering and gain adjustment. The resistors in the input
networks of the preamp and the buffer feedback resistors are
ratio-trimmed for high accuracy.
The output of the preamp drives a gain-of-2 buffer amplifier,
A2, implemented with carefully matched feedback resistors RF.
The 2-stage system architecture of the AD8203 enables the user
to incorporate a low-pass filter prior to the output buffer. By
separating the gain into two stages, a full-scale, rail-to-rail
signal from the preamp can be filtered at Pin 3, and a half-scale
signal, resulting from filtering, can be restored to full scale by
the output buffer amp. The source resistance seen by the
inverting input of A2 is approximately 100 k to minimize the
effects of the input bias current of A2. However, this current is
quite small, and errors resulting from applications that
mismatch the resistance are correspondingly small.
The A2 input bias current has a typical value of 40 nA, however,
this can increase under certain conditions. For example, if the
input signal to the A2 amplifier is VCC/2, the output attempts to
go to VCC due to the gain of 2. However, the output saturates
because the maximum specified voltage for correct operation is
200 mV below VCC. Under these conditions the total input bias
current increases (see Figure 41 for more information).
DIFFERENTIAL MODE VOLTAGE (V)
A2
INPUT
BIAS
CURRENT
(nA)
–140
0
05013-035
–120
–100
–80
–60
–40
–20
0.5
0
1.0
1.5
2.0
2.5
Figure 41. A2 Input Bias Current vs. Input Voltage and Temperature. The
Shaded Area Is the Bias Current from 40°C to +125°C.
相關PDF資料 |
PDF描述 |
|---|---|
| KTR10EZPF4704 | RES 4.70M OHM 1/8W 1% 0805 SMD |
| 0034.5620.22 | FUSE 2A 250V TLAG 5X20 SMD T/R |
| ADA4310-1ACPZ-R2 | IC OPAMP CF DUAL LDIST 16LFCSP |
| 0034.5618.22 | FUSE 1.25A 250V TLAG 5X20SMD TR |
| KTR10EZPF1603 | RES 160K OHM 1/8W 1% 0805 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8203YRMZ-RL | 功能描述:IC AMP DIFF 60KHZ 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8203YRZ | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| AD8203YRZ-R7 | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8203YRZ-RL | 功能描述:IC AMP DIFF 60KHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| AD8205 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single-Supply 42 V System Difference Amplifier |
發布緊急采購，3分鐘左右您將得到回復。