參數資料
型號： AD8197BASTZ
廠商： Analog Devices Inc
文件頁數： 7/28頁
文件大?。?/td> 0K
描述： IC SWITCH DVI/HDMI 4:1 100-LQFP
標準包裝： 1
功能： 開關
電路： 1 x 16:1
電壓電源： 單電源
電壓 - 電源，單路/雙路(±)： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
AD8197B
Rev. 0 | Page 15 of 28
SERIAL CONTROL INTERFACE
RESET
On initial power-up, or at any point in operation, the AD8197B
register set can be restored to the status of the parallel control
interface pins and some preprogrammed default values by
pulling the RESET pin to low, in accordance with the specifica-
tions in Table 1. During normal operation, however, the RESET
pin must be pulled up to 3.3 V. Following a reset, the prepro-
grammed default values of the AD8197B register set correspond
to the state of the parallel interface configuration registers and
defaults, as listed in Table 18. The AD8197B can be controlled
through the parallel control interface until the first serial
control event occurs. As soon as any serial control event occurs,
the serial programming values, corresponding to the state of the
serial interface configuration registers (Table 5), override any
prior parallel programming values, and the parallel control
interface is disabled until the part is subsequently reset.
Note that the input termination resistor switch control is only
via I2C control. Therefore, any system that requires control of
these switches cannot operate in parallel control mode.
WRITE PROCEDURE
To write data to the AD8197B register set, an I2C master (such
as a microcontroller) needs to send the appropriate control
signals to the AD8197B slave device. The signals are controlled
by the I2C master, unless otherwise specified. For a diagram of
the procedure, see Figure 29. The steps for a write procedure are
as follows:
1.
Send a start condition (while holding the I2C_SCL line
high, pull the I2C_SDA line low).
2.
Send the AD8197B part address (seven bits). The upper
four bits of the AD8197B part address are the static value
[1001] and the three LSBs are set by Input Pin I2C_ADDR2,
Input Pin I2C_ADDR1, and Input Pin I2C_ADDR0 (LSB).
This transfer should be MSB first.
3.
Send the write indicator bit (0).
4.
Wait for the AD8197B to acknowledge the request.
5.
Send the register address (eight bits) to which data is to be
written. This transfer should be MSB first.
6.
Wait for the AD8197B to acknowledge the request.
7.
Send the data (eight bits) to be written to the register
whose address was set in Step 5. This transfer should be
MSB first.
8.
Wait for the AD8197B to acknowledge the request.
9.
Perform one of the following:
9a. Send a stop condition (while holding the I2C_SCL
line high, pull the I2C_SDA line high) and release
control of the bus to end the transaction (shown in
9b. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 in this procedure to perform
another write.
9c. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 2 of the read procedure (in the
Read Procedure section) to perform a read from
another address.
9d. Send a repeated start condition (while holding the
I2C_SCL line high, pull the I2C_SDA line low) and
continue with Step 8 of the read procedure (in the
Read Procedure section) to perform a read from the
same address set in Step 5.
R/W
ACK
ADDR
START
FIXED PART
ADDR
REGISTER ADDR
DATA
STOP
ACK
1
2
3
4
5
6
7
8
9
I2C_SCL
GENERAL CASE
I2C_SDA
EXAMPLE
I2C_SDA
*THE SWITCHING/UPDATE DELAY BEGINS AT THE FALLING EDGE OF THE
LAST DATA BIT; FOR EXAMPLE, THE FALLING EDGE JUST BEFORE STEP 8.
*
07
01
5-
0
28
Figure 29. I2C Write Diagram
相關PDF資料
PDF描述
MUX08FQ IC MULTIPLEXER 8X1 16CDIP
DEBB33F471KD3B CAP CER 470PF 3.15KV 10% RADIAL
DEA1X3F820JB3B CAP CER 82PF 3.15KV 5% RADIAL
ADG526AKNZ IC MULTIPLEXER 16X1 28DIP
ADG426BNZ IC MULTIPLEXER 16X1 28DIP
相關代理商/技術參數
參數描述
AD8197BASTZ-RL 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
AD8197BASTZ-RLKL1 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD8197B-EVALZ 制造商:Analog Devices 功能描述:EVAL KIT FOR 4:1 HDMI/DVI SWIT W/ EQUALIZATION - Bulk
AD8197B-XSTZ 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:上次購買時間 類型:視頻開關 應用:HDTV，投影儀，機頂盒 安裝類型:表面貼裝 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:1
AD8197-EVAL 制造商:Analog Devices 功能描述:EVAL KIT FOR 4:1 HDMI/DVI SWIT W/ EQUALIZATION 100LQFP - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*