參數資料
型號： AD8197ASTZ
廠商： Analog Devices Inc
文件頁數： 19/32頁
文件大小： 0K
描述： IC SWITCH DVI/HDMI 4:1 100-LQFP
標準包裝： 1
功能： 開關
電路： 1 x 16:1
電壓電源： 單電源
電壓 - 電源，單路/雙路(±)： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
AD8197
Rev. 0 | Page 26 of 32
The length of cable that can be used in a typical HDMI/DVI
application depends on a large number of factors, including:
Cable quality: the quality of the cable in terms of conductor
wire gauge and shielding. Thicker conductors have lower
signal degradation per unit length.
Data rate: the data rate being sent over the cable. The signal
degradation of HDMI cables increases with data rate.
Edge rates: the edge rates of the source input. Slower input
edges result in more significant data eye closure at the end
of a cable.
Receiver sensitivity: the sensitivity of the terminating
receiver.
As such, specific cable types and lengths are not recommended
for use with a particular equalizer setting. In nearly all applica-
tions, the AD8197 equalization level can be set to high, or 12 dB,
for all input cable configurations at all data rates, without
degrading the signal integrity.
PCB LAYOUT GUIDELINES
The AD8197 is used to switch two distinctly different types of
signals, both of which are required for HDMI and DVI video.
These signal groups require different treatment when laying out
a PC board.
The first group of signals carries the audiovisual (AV) data.
HDMI/DVI video signals are differential, unidirectional, and
high speed (up to 2.25 Gbps). The channels that carry the video
data must be controlled impedance, terminated at the receiver,
and capable of operating at the maximum specified system data
rate. It is especially important to note that the differential traces
that carry the TMDS signals should be designed with a controlled
differential impedance of 100 Ω. The AD8197 provides single-
ended, 50 Ω terminations on-chip for both its inputs and
outputs, and both the input and output terminations can be
enabled or disabled through the serial control interface. The
output terminations can also be enabled or disabled through the
parallel control interface. Transmitter termination is not required
by the HDMI 1.3 standard, but its inclusion improves the overall
system signal integrity.
The audiovisual (AV) data carried on these high speed channels
is encoded by a technique called transmission minimized differ-
ential signaling (TMDS) and in the case of HDMI, is also encrypted
according to the high bandwidth digital copy protection (HDCP)
standard.
The second group of signals consists of low speed auxiliary
control signals used for communication between a source and a
sink. Depending upon the application, these signals can include
the DDC bus (this is an I2C bus used to send EDID information
and HDCP encryption keys between the source and the sink),
the consumer electronics control (CEC) line, and the hot plug
detect (HPD) line. These auxiliary signals are bidirectional, low
speed, and transferred over a single-ended transmission line
that does not need to have controlled impedance. The primary
concern with laying out the auxiliary lines is ensuring that they
conform to the I2C bus standard and do not have excessive
capacitive loading.
TMDS Signals
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. In DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
interleaved with the video data; the DVI standard does not
incorporate audio information. The fourth high speed differ-
ential pair is used for the AV data-word clock, and runs at
one-tenth the speed of the TMDS data channels.
The four high speed channels of the AD8197 are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock, so any channel can be used for any
TMDS signal. The user chooses which signal is routed over
which channel. Additionally, the TMDS channels are symmetrical;
therefore, the p and n of a given differential pair are interchange-
able, provided the inversion is consistent across all inputs and
outputs of the AD8197. However, the routing between inputs
and outputs through the AD8197 is fixed. For example, in quad
mode, Output Channel 0 always switches between Input A0,
Input B0, Input C0, Input D0, and so forth.
The AD8197 buffers the TMDS signals and the input traces can
be considered electrically independent of the output traces. In
most applications, the quality of the signal on the input TMDS
traces is more sensitive to the PCB layout. Regardless of the data
being carried on a specific TMDS channel, or whether the
TMDS line is at the input or the output of the AD8197, all four
high speed signals should be routed on a PCB in accordance
with the same RF layout guidelines.
Layout for the TMDS Signals
The TMDS differential pairs can be either microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stack-up. Additionally, the p and n of each differential pair
must have a controlled differential impedance of 100 Ω. The
characteristic impedance of a differential pair is a function of
several variables including the trace width, the distance separating
the two traces, the spacing between the traces and the reference
plane, and the dielectric constant of the PC board binder material.
Interlayer vias introduce impedance discontinuities that can
cause reflections and jitter on the signal path, therefore, it is
preferable to route the TMDS lines exclusively on one layer of the
board, particularly for the input traces. In some applications, such
as using multiple AD8197s to construct large input arrays, the use
of interlayer vias becomes unavoidable. In these situations, the
input termination feature of the AD8197 improves system signal
integrity by absorbing reflections. Take care to use vias minimally
and to place vias symmetrically for each side of a given differential
pair. Furthermore, to prevent unwanted signal coupling and
相關PDF資料
PDF描述
AD8197BASTZ IC SWITCH DVI/HDMI 4:1 100-LQFP
MUX08FQ IC MULTIPLEXER 8X1 16CDIP
DEBB33F471KD3B CAP CER 470PF 3.15KV 10% RADIAL
DEA1X3F820JB3B CAP CER 82PF 3.15KV 5% RADIAL
ADG526AKNZ IC MULTIPLEXER 16X1 28DIP
相關代理商/技術參數
參數描述
AD8197ASTZ-RL 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
AD8197B 制造商:AD 制造商全稱:Analog Devices 功能描述:4:1 HDMI/DVI Switch with Equalization
AD8197BASTZ 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤
AD8197BASTZ-RL 功能描述:IC SWITCH DVI/HDMI 4:1 100-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
AD8197BASTZ-RLKL1 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*