- 您現在的位置：買賣IC網 > PDF目錄11354 > AD8152JBPZ (Analog Devices Inc)IC CROSSPOINT SWIT 34X34 256BGA PDF資料下載
參數資料
| 型號： | AD8152JBPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/32頁 |
| 文件大小： | 0K |
| 描述： | IC CROSSPOINT SWIT 34X34 256BGA |
| 標準包裝： | 1 |
| 系列： | XStream™ |
| 功能： | 交叉點開關 |
| 電路： | 1 x 34:34 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.25 V ~ 3.63 V |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 256-LBGA 裸露焊盤 |
| 供應商設備封裝： | 256-SBGA（27x27） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
REV. A
–22–
AD8152
The variety of supply configurations cause the need for a supply
agile digital control circuitry. This is done by a programmable
logic device (PLD), which provides instructions to the AD8152.
The PLD supply is typically tied with jumpers across the AD8152’s
VCC and VEE supplies (Jumpers J3 and J4). The PLD is addressed
from the PC by way of digital isolators. These couplers isolate
PC levels from the PLD and allow for any level shifting. If
desired, the user can drive the PLD supply separately as long as
the VEE of the AD8152 and the PLD are tied together (remove
Jumper J3 and leave J4 installed). This allows one to measure
the AD8152 only supply current, for example.
Board Construction or Stack-Up
Figure 11 is a picture of AD8152 evaluation board stack-up from
top to bottom. The layer stack-up has been made symmetrical
to avoid board warpage during manufacture. The microstrip
layout and dimensions are shown in Figure 12. The microstrip
trace width was chosen to be 8 mils. This allows relative ease in
routing through the BGA rows that are 50 mils (1.27 mm) apart.
The outer two out of four rows of high speed signals are routed on
top of the PCB, while the inner two rows are via holed to the
board’s opposite side and then routed outward. Wider microstrip
is desirable for reducing eye height loss versus long traces; how-
ever, the routing will be more difficult as the AD8152 is approached.
The wide microstrip would have to be necked down in width in
order to be routed into the BGA. The necking will increase trace
impedance and therefore induce more signal reflection problems.
MICROSTRIP TRACES
BGA CORNER OUTLINE
VIA HOLE
(GRAY)
CHIP CAPACITOR
(805) SIZE
Figure 13. BGA Corner Capacitor Layout
Figure 12. Cross-Sectional Layout and Dimensioning (To Scale) of Differential
During the layout of the differential microstrip, a software tool
snaps the distance between the two traces to be a constant. If
the distance is not kept constant, impedance variations will
result. These fluctuations can be measured by time domain
reflectometry (TDR).
EXTRA ADDED INDUCTANCE
Figure 14. Poor Capacitor Layout
Bypass Capacitor Layout
The AD8152 8-layer PCB takes advantage of buried interlayer
capacitance. The VEE to VCC planes are placed in the very middle
of the board to make the highest value capacitor. The 4 mil
(0.102 mm) dielectric spacing between VCC/VEE yields 26 nF
of capacitance. Each AD8152 supply pin is directly connected to
its supply plane through a via hole beneath the BGA ball. The
via hole size for a BGA supply pin is slightly bigger than a signal
via. This is to reduce the inductance of the connection, and it
also happens to be a compact layout.
For the chip capacitors, the via holes are placed directly in the
middle of the mounting area and made as large as possible, i.e.,
greater than or equal to 35 mils (0.89 mm). This is to minimize
inductance as much as possible. By minimizing inductance, the
performance of the capacitor or impedance versus frequency
response is not greatly diminished. Note that chip capacitors
will work up to only about 300 MHz.
Figure 14 is an example of a bypass capacitor layout that should
be avoided in any high speed printed circuit board. This layout
connects the chip capacitor mounting pads to small via holes
through a skinny PCB trace. This amounts to four extra inductors
added to the capacitor, two largely from the skinny surface traces
and two from small via holes. Inductance is also variable with
copper thickness and attachment method to power plane. Thermal
relief for soldering purposes also adds unwanted inductance and
should be avoided.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LC73B-04I/SS | IC MCU OTP 4KX14 A/D PWM 28SSOP |
| ADV3201ASWZ | IC CROSSPOINT SWIT 32X32 176LQFP |
| DEA1X3F101JN3A | CAP CER 100PF 3.15KV 5% RADIAL |
| PIC16C57-10/SS | IC MCU OTP 2KX12 28SSOP |
| PIC16C57-10I/SP | IC MCU OTP 2KX12 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8153 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.2 Gbps Single Buffered Mux/Demux Switch |
| AD8153ACPZ | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:XStream™ 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD8153ACPZ-RL7 | 功能描述:IC SW MUX/DEMUX SGL BUFF 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:XStream™ 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD8153-EVALZ | 功能描述:BOARD EVALUATION FOR AD8153 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:XStream™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。