參數資料
型號: AD7982BRMZ
廠商: Analog Devices Inc
文件頁數: 16/24頁
文件大?。?/td> 0K
描述: IC ADC 18BIT 1MSPS PULSAR 10MSOP
產品培訓模塊: Motor Control
設計資源: Converting a Single-Ended Signal with AD7982 Differential PulSAR ADC (CN0032)
Precision Single-Supply Differential ADC Driver for Industrial-Level Signals (CN0180)
標準包裝: 1
系列: PulSAR®
位數: 18
采樣率(每秒): 1M
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 8.6mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
輸入數目和類型: 1 個差分,單極
產品目錄頁面: 780 (CN2011-ZH PDF)
Data Sheet
AD7982
Rev. B | Page 23 of 24
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7982 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7982, with its analog signals on the left side and its digital
signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die, unless a ground plane under the
AD7982 is used as a shield. Fast switching signals, such as CNV
or clocks, should not run near analog signal paths. Crossover of
digital and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog sections. In the latter case,
the planes should be joined underneath the AD7982s.
The AD7982 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the power supplies VDD and VIO of the AD7982
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7982 and connected using short, wide
traces to provide low impedance paths and to reduce the effect
of glitches on the power supply lines.
An example of layout following these rules is shown in
EVALUATING AD7982 PERFORMANCE
Other recommended layouts for the AD7982 are outlined
in the documentation of the evaluation board for the AD7982
(EVAL-AD7982SDZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
06513-
028
AD7982
Figure 41. Example Layout of the AD7982 (Top Layer)
06513-
029
Figure 42. Example Layout of the AD7982 (Bottom Layer)
相關PDF資料
PDF描述
VI-21R-IW-F4 CONVERTER MOD DC/DC 7.5V 100W
VI-21R-IW-F3 CONVERTER MOD DC/DC 7.5V 100W
LTC1605IN#PBF IC A/D CONV 16BIT SAMPLNG 28-DIP
VI-J1J-MW-F2 CONVERTER MOD DC/DC 36V 100W
VI-21R-IW-F2 CONVERTER MOD DC/DC 7.5V 100W
相關代理商/技術參數
參數描述
AD7982BRMZRL7 功能描述:IC ADC 18BIT 7.0MW 1MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD7983 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 1.33 MSPS PulSAR ADC in MSOP/QFN
AD79831 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN)
AD7983BCPZ-R2 功能描述:IC ADC 16BIT 1.33MSPS 10LFCSP 制造商:analog devices inc. 系列:* 包裝:帶卷(TR) 零件狀態:Digi-Key 停止供應 封裝/外殼:10-WFDFN 裸露焊盤,CSP 供應商器件封裝:10-LFCSP-WD(3x3) 標準包裝:250
AD7983BCPZ-RL 功能描述:IC ADC 16BIT 1.33MSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極