- 您現在的位置：買賣IC網 > PDF目錄10657 > AD7982BRMZ (Analog Devices Inc)IC ADC 18BIT 1MSPS PULSAR 10MSOP PDF資料下載
參數資料
| 型號： | AD7982BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 1MSPS PULSAR 10MSOP |
| 產品培訓模塊： | Motor Control |
| 設計資源： | Converting a Single-Ended Signal with AD7982 Differential PulSAR ADC (CN0032) Precision Single-Supply Differential ADC Driver for Industrial-Level Signals (CN0180) |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 8.6mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極 |
| 產品目錄頁面： | 780 (CN2011-ZH PDF) |
Data Sheet
AD7982
Rev. B | Page 19 of 24
CS MODE, 4-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when multiple AD7982s are
connected to an SPI-compatible digital host.
A connection diagram example using two AD7982s is shown in
Figure 33, and the corresponding timing is given in Figure 34.
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned high before the minimum conversion
time elapses and then held high for the maximum possible
conversion time to avoid the generation of the busy signal
indicator. When the conversion is complete, the AD7982 enters
the acquisition phase and powers down. Each ADC result can
be read by bringing its SDI input low, which consequently
outputs the MSB onto SDO. The remaining data bits are then
clocked by subsequent SCK falling edges. The data is valid on
both SCK edges. Although the rising edge can be used to
capture the data, a digital host using the SCK falling edge allows
a faster reading rate, provided it has an acceptable hold time.
After the 18th SCK falling edge or when SDI goes high (whichever
occurs first), SDO returns to high impedance and another
AD7982 can be read.
AD7982
SDI
SDO
CNV
SCK
CONVERT
DATA IN
CLK
DIGITAL HOST
06513-
020
CS1
CS2
AD7982
SDI
SDO
CNV
SCK
Figure 33. CS Mode, 4-Wire Without Busy Indicator Connection Diagram
SDO
D17
D16
D15
D1
D0
tDIS
SCK
1
2
3
34
35
36
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI(CS1)
CNV
tSSDICNV
tHSDICNV
D1
16
17
tSCK
tSCKL
tSCKH
D0
D17
D16
19
20
18
SDI(CS2)
06513-
021
Figure 34. CS Mode, 4-Wire Without Busy Indicator Serial Interface Timing
相關PDF資料 |
PDF描述 |
|---|---|
| VI-21R-IW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
| VI-21R-IW-F3 | CONVERTER MOD DC/DC 7.5V 100W |
| LTC1605IN#PBF | IC A/D CONV 16BIT SAMPLNG 28-DIP |
| VI-J1J-MW-F2 | CONVERTER MOD DC/DC 36V 100W |
| VI-21R-IW-F2 | CONVERTER MOD DC/DC 7.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7982BRMZRL7 | 功能描述:IC ADC 18BIT 7.0MW 1MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯(lián) 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7983 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 1.33 MSPS PulSAR ADC in MSOP/QFN |
| AD79831 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7983BCPZ-R2 | 功能描述:IC ADC 16BIT 1.33MSPS 10LFCSP 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態(tài):Digi-Key 停止供應 封裝/外殼:10-WFDFN 裸露焊盤，CSP 供應商器件封裝:10-LFCSP-WD（3x3） 標準包裝:250 |
| AD7983BCPZ-RL | 功能描述:IC ADC 16BIT 1.33MSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯(lián) 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。