- 您現在的位置：買賣IC網 > PDF目錄10343 > AD7920BKSZ-REEL (Analog Devices Inc)IC ADC 12BIT SRL 250KSPS SC70-6 PDF資料下載
參數資料
| 型號： | AD7920BKSZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SRL 250KSPS SC70-6 |
| 標準包裝： | 10,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 250k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 15mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-TSSOP，SC-88，SOT-363 |
| 供應商設備封裝： | SC-70-6 |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極 |
| 配用： | EVAL-AD7920CBZ-ND - BOARD EVALUATION FOR AD7920 |
AD7910/AD7920
Rev. C | Page 15 of 24
AD7910/
AD7920
VDD
VIN
SERIAL
INTERFACE
0V TO VDD
INPUT
μC/μP
GND
SCLK
SDATA
CS
0.1
μF
10
μF
1
μF
TANT
0.1
μF
680nF
3V
5V
SUPPLY
1.2mA
REF193
02976-017
Figure 17. REF193 as Power Supply
Table 6 provides typical performance data with various
references used as a VDD source for a 100 kHz input tone at
room temperature, under the same setup conditions.
Table 6. AD7920 Typical Performance for Various Voltage
References IC
Reference Tied to VDD
AD7920 SNR Performance (dB)
AD780 @ 3 V
72.65
72.35
AD780 @ 2.5 V
72.5
72.2
72.6
ANALOG INPUT
Figure 18 shows an equivalent circuit of the analog input
structure of the AD7910/AD7920. The two diodes, D1 and D2,
provide ESD protection for the analog input. Care must be
taken to ensure that the analog input signal never exceeds the
supply rails by more than 300 mV. This causes these diodes to
become forward biased and start conducting current into the
substrate. The maximum current these diodes can conduct
without causing irreversible damage to the parties is 10 mA.
Capacitor C1 in Figure 18 is typically about 6 pF and can be
attributed primarily to pin capacitance. Resistor R1 is a lumped
component made up of the on resistance of a switch. This
resistor is typically about 100 Ω. Capacitor C2 is the ADC
sampling capacitor and has a capacitance of 20 pF typically. For
ac applications, removing high frequency components from the
analog input signal is recommended by use of a band-pass filter
on the relevant analog input pin. In applications where
harmonic distortion and signal-to-noise ratio are critical, the
analog input should be driven from a low impedance source.
Large source impedances significantly affect the ac performance
of the ADC. This can necessitate the use of an input buffer
amplifier. The choice of the op amp is a function of the
particular application.
C1
6pF
C2
20pF
R1
D1
D2
CONVERSION PHASE—SWITCH OPEN
TRACK PHASE—SWITCH CLOSED
VDD
VIN
02976-018
Figure 18. Equivalent Analog Input Circuit
Table 7 provides some typical performance data with various op
amps used as the input buffer for a 100 kHz input tone at room
temperature, under the same setup conditions.
Table 7. AD7920 Typical Performance for Various Input
Buffers, VDD = 3 V
Op Amp in the Input Buffer
AD7920 SNR Performance (dB)
72.3
72.5
71.4
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases, and performance degrades (see
DIGITAL INPUTS
The digital inputs applied to the AD7910/AD7920 are not limited
by the maximum ratings that limit the analog input. Instead, the
digital inputs applied can go to 7 V and are not restricted by the
VDD + 0.3 V limit as on the analog input. For example, if the
AD7910/AD7920 were operated with a VDD of 3 V, then 5 V logic
levels could be used on the digital inputs. However, it is important
to note that the data output on SDATA still have 3 V logic levels
when VDD = 3 V. Another advantage of SCLK and CS not being
restricted by the VDD + 0.3 V limit is that power supply
sequencing issues are avoided. If CS or SCLK is applied before
VDD, there is no risk of latch-up as there would be on the analog
inputs if a signal greater than 0.3 V were applied prior to VDD.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473E10F35SD | CONN PLUG 13POS STRAIGHT W/SCKT |
| AD7477AARMZ-REEL | IC ADC 10BIT 1MSPS 8-MSOP |
| MS27473E10F35SB | CONN PLUG 13POS STRAIGHT W/SCKT |
| LTC2481HDD#PBF | IC ADC 16BIT I2C 7.5SPS 10DFN |
| MS27499E10B99P | CONN RCPT 7POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7920BKSZ-REEL7 | 功能描述:IC ADC 12BIT SRL 250KSPS SC70-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7920BRM | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin MSOP 制造商:Rochester Electronics LLC 功能描述:12-BIT 250KSPS ADC MICRO SOIC PKG I.C. - Bulk 制造商:Analog Devices 功能描述:IC 12BIT ADC SMD 7920 MSOP8 |
| AD7920BRM-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin MSOP T/R |
| AD7920BRM-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin MSOP T/R |
| AD7920BRMZ | 功能描述:IC ADC 12BIT 250KSPS 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。