- 您現在的位置：買賣IC網 > PDF目錄9481 > AD7890ARZ-10REEL (Analog Devices Inc)IC DAS 12BIT 8CH 24-SOIC PDF資料下載
參數資料
| 型號： | AD7890ARZ-10REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 12BIT 8CH 24-SOIC |
| 產品培訓模塊： | Power Line Monitoring |
| 標準包裝： | 1,000 |
| 類型： | 數據采集系統（DAS） |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 117k |
| 數據接口： | 串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 5V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7890
Rev. C | Page 11 of 28
THEORY OF OPERATION
CONVERTER DETAILS
The AD7890 is an 8-channel, 12-bit, single supply, serial data
acquisition system. It provides the user with signal scaling,
multiplexer, track/hold, reference, ADC, and versatile serial
logic functions on a single chip. The signal scaling allows the
part to handle ±10 V input signals (AD7890-10) and 0 V to
4.096 V input signals (AD7890-4) while operating from a single
5 V supply. The AD7890-2 contains no signal scaling and
accepts an analog input range of 0 V to 2.5 V. The part operates
from a 2.5 V reference, which can be provided from the part’s
own internal reference or from an external reference source.
Unlike other single chip data acquisition solutions, the AD7890
provides the user with separate access to the multiplexer and
the ADC. This means that the flexibility of separate multiplexer
and ADC solutions is not sacrificed with the one-chip solution.
With access to the multiplexer output, the user can implement
external signal conditioning between the multiplexer and the
track/hold. It means that one antialiasing filter can be used on
the output of the multiplexer to provide the antialiasing
function for all eight channels.
Conversion is initiated on the AD7890 either by pulsing the
CONVST input or by writing a Logic 1 to the CONV bit of the
control register. When using the hardware CONVST input, on
the rising edge of the CONVST signal, the on-chip track/hold
goes from track to hold mode and the conversion sequence is
started, provided the internal pulse has timed out. This internal
pulse (which appears at the CEXT pin) is initiated whenever the
multiplexer address is loaded to the AD7890 control register.
This pulse goes from high to low when a serial write to the part
is initiated. It starts to discharge on the sixth falling clock edge
of SCLK in a serial write operation to the part. The track/hold
cannot go into hold and conversion cannot be initiated until the
CEXT pin has crossed its trigger point of 2.5 V. The discharge
time of the voltage on CEXT depends upon the value of capacitor
connected to the CEXT pin (see the CEXT Functioning section).
The fact that the pulse is initiated every time a write to the
control register takes place means that the software conversion
start and track/hold signal is always delayed by the internal pulse.
The conversion clock for the part is generated from the clock
signal applied to the CLK IN pin of the part. Conversion time
for the AD7890 is 5.9 μs from the rising edge of the hardware
CONVST signal and the track/hold acquisition time is 2 μs. To
obtain optimum performance from the part, the data read
operation or control register write operation should not occur
during the conversion or during 500 ns prior to the next
conversion.
This allows the part to operate at throughput rates up to
117 kHz in the external clocking mode and achieve data sheet
specifications. The part can operate at slightly higher
throughput rates (up to 127 kHz), again in external clocking
mode with degraded performance (see the Timing and Control
section). The throughput rate for self-clocking mode is limited
by the serial clock rate to 78 kHz.
All unused inputs should be connected to a voltage within the
nominal analog input range to avoid noise pickup. On the
AD7890-10, if any one of the input channels which are not
being converted goes more negative than 12 V, it can interfere
with the conversion on the selected channel.
CIRCUIT DESCRIPTION
The AD7890 is offered as three part types: the AD7890-10
handles a ±10 V input voltage range, the AD7890-4 handles a
0 V to 4.096 V input range, while the AD7890-2 handles a 0 V
to 2.5 V input voltage range.
AD7890-10 Analog Input
Figure 4 shows the analog input section for the AD7890-10. The
analog input range for each of the analog inputs is ±10 V into
an input resistance of typically 33 kΩ. This input is benign with
no dynamic charging currents with the resistor attenuator stage
followed by the multiplexer and, in cases where MUX OUT is
connected to SHA IN, this is followed by the high input
impedance stage of the track/hold amplifier. The designed code
transitions occur on successive integer LSB values (such as:
1 LSB, 2 LSBs, 3 LSBs...). Output coding is twos complement
binary with 1 LSB FSR/4096 = 20 V/4096 = 4.88 mV. The
ideal input/output transfer function is shown in Table 4.
2.5V
REFERENCE
30k
2k
7.5k
2001
10k
AD7890-10
REF OUT/
REF IN
AGND
VINX
1EQUIVALENT ON-RESISTANCE OF MULTIPLEXER
MUX OUT
TO ADC
REFERENCE
CIRCUITRY
01
35
7-
0
4
Figure 4. AD7890-10 Analog Input Structure
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B11-IU-F4 | CONVERTER MOD DC/DC 12V 200W |
| VI-B0P-MY-S | CONVERTER MOD DC/DC 13.8V 50W |
| V24A3V3M200BL2 | CONVERTER MOD DC/DC 3.3V 200W |
| AD7890ARZ-2REEL | IC DAS 12BIT 8CH 24-SOIC |
| V24A3V3M200BF3 | CONVERTER MOD DC/DC 3.3V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7890ARZ-2 | 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7890ARZ-2REEL | 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7890ARZ-4 | 功能描述:IC DAS 12BIT 8CH 24SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7890ARZ-4REEL | 功能描述:IC DAS 12BIT 8CH 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD7890BN-10 | 功能描述:IC DAS 12BIT 8CH 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。