If fDCLK = 20 MHz (maximum), then t
參數資料
型號： AD7877ACBZ-REEL7
廠商： Analog Devices Inc
文件頁數： 19/45頁
文件大?。?/td> 0K
描述： IC CTRLR TOUCH SCREEN 25-WLCSP
標準包裝： 1
類型： 電阻
觸摸面板接口： 4 線
輸入數/鍵： 1 TSC
分辨率（位）： 12 b
評估套件： 可供
數據接口： 串行，SPI?
數據速率/采樣率 (SPS，BPS)： 125k
電壓基準： 外部，內部
電源電壓： 2.7 V ~ 5.25 V
電流 - 電源： 1µA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 25-UFBGA，WLCSP
供應商設備封裝： 25-WLCSP
包裝： 標準包裝
產品目錄頁面： 779 (CN2011-ZH PDF)
配用： EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877
其它名稱： AD7877ACBZ-REEL7DKR
Data Sheet
AD7877
Rev. D | Page 25 of 44
If fDCLK = 20 MHz (maximum), then tDCLK = 50 ns.
t2 = 512 s with timer set to 1024 (TMR bits = 01b)
tWRITE = tREAD = 16 CLK period × tDCLK = 800 ns
t3 = maximum time taken to write read address and read
11 registers = 800 ns (write) + [800 ns (read) × 11] = 9.6 s.
t4MAX = t2 t3 = 512 s 9.6 s = 502.4 s
Pen Interrupt (PENIRQ)
The pen interrupt request output (PENIRQ) goes low whenever
the screen is touched. The pen interrupt equivalent output
circuitry is outlined in Figure 43. This is a digital logic output
with an internal pull-up resistor of 50 k, which means it does
not need an external pull-up. The PENIRQ output idles high.
The PENIRQ circuitry is always enabled, except during
conversions.
03796-021
X+
TOUCH
SCREEN
Y+
50k
Y–
X–
PENIRQ
ENABLE
PENIRQ
VCC
Figure 43. PENIRQ Output Equivalent Circuit
When the screen is touched, PENIRQ goes low. This generates
an interrupt request to the host. When the screen touch ends,
and if the ADC is idle, PENIRQ immediately goes high. If the
ADC is converting, PENIRQ goes high once the ADC becomes
idle. The PENIRQ operation for these two conditions is shown
03796-022
SCREEN
PENIRQ
ADC
STATUS
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
NOT
TOUCHED
ADC IDLE
SCREEN
PENIRQ
ADC
STATUS
TOUCHED
ADC IDLE
ADC
CONVERTING
ADC IDLE
RELEASE NOT
DETECTED
PENIRQ
DETECTS
RELEASE
PENIRQ
DETECTS
RELEASE
PENIRQ
DETECTS
TOUCH
PENIRQ
DETECTS
TOUCH
Figure 44. PENIRQ Operation for ADC Idle and ADC Converting
SYNCRONIZING THE AD7877 TO THE HOST CPU
The two suggested methods for synchronizing the AD7877
to its host CPU are slave mode, in which the mode bits can
be either 01b or 10b, and master mode, in which the mode
bits are 11b.
In slave mode, PENIRQ can be used as an interrupt to the host.
When PENIRQ goes low to indicate that the screen has been
touched, the host is awakened. The host can then program the
AD7877 to begin converting in either Mode 01b or Mode 10b,
and can read the result registers after the conversions are
completed.
In master mode, DAV can also be used as an interrupt to the
host. However, the host should first initialize the AD7877 in
Mode 11b. The host can then go into sleep mode to conserve
power. The wake-up on touch feature of the AD7877 is active in
this mode, therefore, when the screen is touched, the
programmed sequence of conversions begins automatically.
When the DAV signal asserts, the host reads the new data avail-
able in the AD7877 results registers and returns to sleep mode.
This method can significantly reduce the load on the host.
相關PDF資料
PDF描述
MS27484T22A35SB CONN PLUG 100POS STRAIGHT W/SCKT
MS27468T25B35SD CONN RCPT 128POS JAM NUT W/SCKT
MS27468E25B35SD CONN RCPT 128POS JAM NUT W/SCKT
MAX11811ETP+ IC TOUCH SCREEN 12BIT I2C 20TQFN
MXB7843EEE+ IC CNTRLR TOUCH RES 16QSOP
相關代理商/技術參數
參數描述
AD7877ACP 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk
AD7877ACP-500RL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER
AD7877ACP-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:Touch Screen Controller
AD7877ACP-REEL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER
AD7877ACPZ 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*