- 您現在的位置：買賣IC網 > PDF目錄10537 > AD7854ARSZ (Analog Devices Inc)IC ADC 12BIT PARALLEL LP 28-SSOP PDF資料下載
參數資料
| 型號： | AD7854ARSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT PARALLEL LP 28-SSOP |
| 標準包裝： | 47 |
| 位數： | 12 |
| 采樣率（每秒）： | 200k |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 30mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極；1 個偽差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁
AD7854/AD7854L
–6–
REV. B
PIN FUNCTION DESCRIPTIONS
Pin
Mnemonic
Description
1
CONVST
Convert Start. Logic input. A low to high transition on this input puts the track/hold into its hold
mode and starts conversion. When this input is not used, it should be tied to DVDD.
2
WR
Write Input. Active low logic input. Used in conjunction with
CS and HBEN to write to internal registers.
3
RD
Read Input. Active low logic input. Used in conjunction with
CS and HBEN to read from internal
registers.
4
CS
Chip Select Input. Active low logic input. The device is selected when this input is active.
5
REFIN/
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the
REFOUT
reference source for the analog-to-digital converter. The nominal reference voltage is 2.5 V and this appears
at the pin. This pin can be overdriven by an external reference and can be taken as high as AVDD. When
this pin is tied to AVDD, then the CREF1 pin should also be tied to AVDD.
6AVDD
Analog Positive Supply Voltage, +3.0 V to +5.5 V.
7
AGND
Analog Ground. Ground reference for track/hold, reference and DAC.
8CREF1
Reference Capacitor (0.1
F multilayer ceramic). This external capacitor is used as a charge source for the
internal DAC. The capacitor should be tied between the pin and AGND.
9CREF2
Reference Capacitor (0.01
F ceramic disc). This external capacitor is used in conjunction with the on-chip
reference. The capacitor should be tied between the pin and AGND.
10
AIN(+)
Analog Input. Positive input of the pseudo-differential analog input. Cannot go below AGND or above
AVDD at any time, and cannot go below AIN(–) when the unipolar input range is selected.
11
AIN(–)
Analog Input. Negative input of the pseudo-differential analog input. Cannot go below AGND or above
AVDD at any time.
12
HBEN
High Byte Enable Input. The AD7854 operates in byte mode only but outputs 12 bits of data during a read
cycle with HBEN low. When HBEN is high, then the high byte of data that is written to or read from the
part is on DB0 to DB7. When HBEN is low, then the lowest byte of data being written to the part is on
DB0 to DB7. If reading from the part with HBEN low, then the lowest 12 bits of data appear on pins DB0
to DB11. This allows a single read from the ADC or from the control register in a 16-bit bus system.
However, two reads are needed to access the calibration registers. Also, two writes are necessary to write to
any of the registers.
13–21
DB0–DB8
Data Bits 0 to 8. Three state data I/O pins that are controlled by
CS, RD, WR and HBEN. Data output is
straight binary (unipolar mode) or twos complement (bipolar mode).
22
DVDD
Digital Supply Voltage, +3.0 V to +5.5 V.
23
DGND
Digital Ground. Ground reference point for digital circuitry.
24–26
DB9–DB11
Data Bits 9 to 11. Three state data output pins that are controlled by
CS, RD and HBEN. Data output is
straight binary (unipolar mode) or twos complement (bipolar mode). These output pins should be tied to
DVDD via 100 k
resistors when the AD7854/AD7854L is being interfaced to an 8-bit data bus.
27
CLKIN
Master Clock Signal for the device (4 MHz for AD7854, 1.8 MHz for AD7854L). Sets the conversion and
calibration times.
28
BUSY
Busy Output. The busy output is triggered high by the falling edge of
CONVST and remains high until
conversion is completed. BUSY is also used to indicate when the AD7854/AD7854L has completed its on-
chip calibration sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7828BRZ | IC ADC 8BIT 8CHAN HS 28SOIC |
| AD7657BSTZ-1 | IC ADC 14BIT 6CH 250KSPS 64LQFP |
| AD7824KRZ | IC ADC 8BIT LC2MOS 4CH HS 24SOIC |
| VI-B4J-MX-F4 | CONVERTER MOD DC/DC 36V 75W |
| AD7820KRZ | IC ADC 8BIT HS TRACK/HOLD 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7854ARZ | 功能描述:IC ADC 12BIT PARALLEL LP 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7854ARZ-REEL | 功能描述:IC ADC 12BIT PARALLEL LP 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7854BR | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 28-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:12-BIT SINGLE CH.PARALLEL ADC I.C. - Bulk |
| AD7854BR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 200ksps 12-bit Parallel 28-Pin SOIC W T/R |
| AD7854BRZ | 功能描述:IC ADC 12BIT PARALLEL LP 28-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發布緊急采購，3分鐘左右您將得到回復。