- 您現在的位置：買賣IC網 > PDF目錄10154 > AD7851KN (Analog Devices Inc)IC ADC 14BIT SRL 333KSPS 24-DIP PDF資料下載
參數資料
| 型號： | AD7851KN |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 35/36頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SRL 333KSPS 24-DIP |
| 標準包裝： | 15 |
| 位數： | 14 |
| 采樣率（每秒）： | 333k |
| 數據接口： | 8051，QSPI?，串行，SPI? µP |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極；1 個偽差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁
AD7851
–8–
REV. B
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The end-
points of the transfer function are zero scale, a point 1/2 LSB
below the first code transition, and full scale, a point 1/2 LSB
above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Total Unadjusted Error
This is the deviation of the actual code from the ideal code tak-
ing all errors into account (gain, offset, integral nonlinearity, and
other errors) at any point along the transfer function.
Unipolar Offset Error
This is the deviation of the first code transition (00 . . . 000 to
00 . . . 001) from the ideal AIN(+) voltage (AIN(–) + 1/2 LSB)
when operating in unipolar mode.
Positive Full-Scale Error
This applies to unipolar and bipolar modes and is the deviation of
the last code transition from the ideal AIN(+) voltage (AIN(–) +
full scale – 1.5 LSB) after the offset error has been adjusted out.
Negative Full-Scale Error
This applies to bipolar mode only and is the deviation of the
first code transition (10 . . . 000 to 10 . . . 001) from the ideal
AIN(+) voltage (AIN(–) – VREF/2 + 0.5 LSB).
Bipolar Zero Error
This is the deviation of the midscale transition (all 1s to all 0s)
from the ideal AIN(+) voltage (AIN(–) – 1/2 LSB).
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode at the end
of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within
±1/2 LSB, after the end of conversion.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitiza-
tion process; the more levels, the smaller the quantization noise.
The theoretical signal-to-(noise + distortion) ratio for an ideal
N-bit converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N +1.76)dB
Thus, for a 14-bit converter, this is 86 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7851, it is defined as
THD
VVV
VV
V
(d )
20 log
B
=
++
()
2
3
2
4
2
5
2
6
2
1
where V1 is the rms amplitude of the fundamental and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for parts
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
± nfb where
m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are
those for which neither m nor n are equal to zero. For example,
the second-order terms include (fa + fb) and (fa – fb), while the
third-order terms include (2fa + fb), (2fa – fb), (fa + 2fb), and
(fa – 2fb).
Testing is performed using the CCIF standard where two
input frequencies near the top end of the input bandwidth are
used. In this case, the second-order terms are usually distanced
in frequency from the original sine waves while the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
Power Supply Rejection Ratio (PSRR)
PSRR is defined as the ratio of the power in ADC output at fre-
quency f to the power of the full-scale sine wave applied to the
supply voltage (VDD). The units are in LSB, % of FS per % of
supply voltage, or expressed logarithmically, in dB (PSRR (dB)
= 10 log (Pf/Pfs)).
Full Power Bandwidth (FPBW)
FPBW is that frequency at which the amplitude of the recon-
structed fundamental (using FFTs and neglecting harmonics
and SNR) is reduced by 3 dB for a full-scale input.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J3M-MW-B1 | CONVERTER MOD DC/DC 10V 100W |
| MS3106F28-5PW | CONN PLUG 5POS STRAIGHT W/PINS |
| VI-J3L-MW-B1 | CONVERTER MOD DC/DC 28V 100W |
| LTC2364IMS-18#TRPBF | IC ADC 18BIT 250K 1CH 16MSOP |
| VI-J3K-MW-B1 | CONVERTER MOD DC/DC 40V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7851KNZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7851KR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7851KR-REEL | 制造商:Analog Devices 功能描述: |
| AD7851KRZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7851KRZ3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。