- 您現在的位置：買賣IC網 > PDF目錄10154 > AD7851KN (Analog Devices Inc)IC ADC 14BIT SRL 333KSPS 24-DIP PDF資料下載
參數資料
| 型號： | AD7851KN |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT SRL 333KSPS 24-DIP |
| 標準包裝： | 15 |
| 位數： | 14 |
| 采樣率（每秒）： | 333k |
| 數據接口： | 8051，QSPI?，串行，SPI? µP |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極；1 個偽差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
–31–
REV. B
AD7851
(8XC51/L51)
/PIC17C42
P3.0/DT
P3.1/CK
AD7851
CONVST
CLKIN
SCLK
DIN
SYNC
SM1
SM2
POLARITY
OPTIONAL
7MHz/6MHz
BUSY
(
INT0/P3.2)/INT
DGND FOR 8XC51/L51
DVDD FOR PIC17C42
MASTER
SLAVE
OPTIONAL
Figure 45. 8XC51/PIC17C42 Interface
AD7851 to 68HC11/16/L11/PIC16C42 Interface
Figure 46 shows the AD7851 SPI/QSPI interface to the
68HC11/16/L11/PIC16C42. The
SYNC line is not used and is
tied to DGND. The
Controller is configured as the master by
setting the MSTR bit in the SPCR to 1, and thus provides the
serial clock on the SCK pin. For all the
Controllers, the CPOL
bit is set to 1, and for the 68HC11/16/L11, the CPHA bit is set
to 1. The CLKIN and
CONVST signals can be supplied from
the
Controller or from separate sources. The BUSY signal can
be used as an interrupt to tell the
Controller when the conver-
sion is finished, then the reading and writing can take place. If
required, the reading and writing can take place during conver-
sion and there will be no need for the BUSY signal in this case.
For no writing to the part then the DIN pin can be tied perma-
nently low. For the 68HC16 and the QSPI interface, the SM2
pin should be tied high and the
SS line tied to the SYNC pin.
The microsequencer on the 68HC16 QSPI port can be used for
performing a number of read and write operations independent
of the CPU and storing the conversion results in memory with-
out taxing the CPU. The typical sequence of events would be
writing to the control register via the DIN line setting a conversion
start and at the same time reading data from the previous conver-
sion on the DOUT line, wait for the conversion to be finished
(3.25
s with 6 MHz CLKIN), and then repeat the sequence. The
maximum serial frequency will be determined by the data access
and hold times of the
Controllers and the AD7851.
68HC11/16/
L11/PIC16C42
SCK
SS
AD7851
CONVST
CLKIN
SCLK
DOUT
BUSY
SM1
SM2
POLARITY
OPTIONAL
7MHz/6MHz
SYNC
MISO
DIN AT DGND FOR
NO WRITING TO PART
MASTER
SLAVE
DIN
DVDD
OPTIONAL
IRQ
MOSI
DVDDFOR HC11, SPI
DGND FOR HC16, QSPI
DVDD
SPI
HC16, QSPI
Figure 46. 68HC11 and 68HC16 Interface
MICROPROCESSOR INTERFACING
In many applications, the user may not require the facility of
writing to the on-chip registers. The user may just want to
hardwire the relevant pins to the appropriate levels and read
the conversion result. In this case, the DIN pin can be tied low
so that the on-chip registers are never used. Now the part will
operate as a nonprogrammable analog-to-digital converter where
the
CONVST is applied, a conversion is performed, and the result
may be read using the SCLK to clock out the data from the output
register on to the DOUT pin. Note that the DIN pin cannot be
tied low when using the 2-wire interface mode of operation.
The SCLK can also be connected to the CLKIN pin if the user
does not want to have to provide separate serial and master
clocks in Interface Modes 1, 2, and 3. With this arrangement,
the
SYNC signal must be low for 16 SCLK cycles in Interface
Modes 1 and 2 for the read and write operations. For Interface
Mode 3, the
SYNC can be low for more than 16 SCLK cycles
for the read and write operations. Note that in Interface Modes 4
and 5 the CLKIN and SCLK cannot be tied together as the
SCLK is an output and the CLKIN is an input.
DIN
DOUT
SYNC
CONVST
CLKIN
SCLK
AD7851
7 MHz/6MHz
MASTER
CLOCK
SYNC SIGNAL
TO GATE
THE SCLK
SERIAL DATA
OUTPUT
CONVERSION
START
Figure 44. Simplified Interface Diagram with DIN
Grounded and SCLK Tied to CLKIN
AD7851 to 8XC51/PIC17C42 Interface
Figure 45 shows the AD7851 interface to the 8XC51/PIC17C42,
which only runs at 5 V. The 8XC51 is in Mode 0 operation.
This is a 2-wire interface consisting of the SCLK and the DIN
which acts as a bidirectional line. The
SYNC is tied low. The
BUSY line can be used to give an interrupt driven system but
this would not normally be the case with the 8XC51/PIC17C42.
For the 8XC51, 12 MHz version, the serial clock will run at a
maximum of 1 MHz so that the serial interface to the AD7851
will only be running at 1 MHz. The CLKIN signal must be pro-
vided separately to the AD7851 from a port line on the 8XC51
or from a source other than the 8XC51. Here the SCLK cannot
be tied to the CLKIN as the 8XC51 only provides a noncon-
tinuous serial clock. The
CONVST signal can be provided from
an external timer or conversion can be started in software if
required. The sequence of events would typically be writing to
the control register via the DIN line setting a conversion start
and the 2-wire interface mode (this would be performed in two
8-bit writes), wait for the conversion to be finished (3.25
s with
6 MHz CLKIN), read the conversion result data on the DIN line
(this would be performed in two 8-bit reads), and then repeat the
sequence. The maximum serial frequency will be determined by
the data access and hold times of the 8XC51/PIC17C42 and the
AD7851.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J3M-MW-B1 | CONVERTER MOD DC/DC 10V 100W |
| MS3106F28-5PW | CONN PLUG 5POS STRAIGHT W/PINS |
| VI-J3L-MW-B1 | CONVERTER MOD DC/DC 28V 100W |
| LTC2364IMS-18#TRPBF | IC ADC 18BIT 250K 1CH 16MSOP |
| VI-J3K-MW-B1 | CONVERTER MOD DC/DC 40V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7851KNZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7851KR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7851KR-REEL | 制造商:Analog Devices 功能描述: |
| AD7851KRZ | 功能描述:IC ADC 14BIT SRL 333KSPS 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7851KRZ3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit 333 kSPS Serial A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。