- 您現在的位置：買賣IC網 > PDF目錄1983 > AD7811YRZ-REEL7 (Analog Devices Inc)IC ADC 10BIT 4CHAN SRL 16SOIC PDF資料下載
參數資料
| 型號： | AD7811YRZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 4CHAN SRL 16SOIC |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 1,000 |
| 位數： | 10 |
| 采樣率（每秒）： | 350k |
| 數據接口： | DSP，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 10.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極；3 個偽差分，單極 |
AD7811/AD7812
–8–
REV. B
Control Register (AD7812)
The Control Register is a 10-bit-wide, write only register. The Control Register is written to when the AD7812 receives a falling
edge on its TFS pin. The AD7812 will maintain the same configuration until a new control byte is written to the part. The control
register can be written to at the same time data is being read. This latter feature enhances throughput rates when software control is
being used or when the analog input channels are being changed frequently. The power-up default register contents are all zeros;
therefore, when the supplies are connected, the AD7812 is powered down by default.
Control Register AD7812
9
0
A1
D
P0
D
PV 8
N
I
/
D
N
G
A
/
F
I
D
L
G
S
2
H
C1
H
C0
H
C
T
S
V
N
O
C
F
E
R
T
X
E
A0
This is the package address bit. It is used in conjunction with the package address pin to allow two AD7812s to
share the same serial bus. The AD7812 can also share the same serial bus with the AD7811. When a control word
is written to the control register of the AD7812 the control word is ignored if the package address bit in the con-
trol byte does not match how the package address pin is hardwired. Only the serial port of the device which
received the last valid control byte, i.e., the address bit matched the address pin, will attempt to drive the serial bus
on the next serial read. When the part powers up this bit is set to 0.
PD1, PD0
These bits allow the AD7812 to be fully powered down and powered up. Bit combinations PD1 = PD0 = 0 and
PD1 = PD0 = 1 override the automatic power-down decision at the end of conversion. These bits also decide the
power-down mode when the AD7812 enters a power-down at the end of a conversion. There are two power-down
modes—Full Power-Down and Partial Power-Down. See Power-Down section of this data sheet.
PD1
PD0
Description
0
Full Power-Down of the AD7812
0
1
Partial Power-Down at the End of Conversion
1
0
Full Power-Down at the End of Conversion
1
Power-Up the AD7812
VIN8/AGND
The DIF/
SGL bit in the control register must be set to 0 in order to use this option otherwise this bit is ignored.
Setting VIN8/AGND to 0 configures the analog inputs of the AD7812 as eight single-ended analog inputs
referenced to analog ground (AGND). By setting this bit to 1 the input channels VIN1 to VIN7 are configured
as seven pseudo differential channels with respect to VIN8—see Table II.
DIF/
SGL
This bit is used to configure the analog inputs as single ended or pseudo differential pairs. By setting this bit to 0
the analog inputs can be configured as single ended with respect to AGND, or pseudo differential with respect to
VIN8 as explained above. Setting this bit to 1 configures the analog input channels as four pseudo differential pairs
VIN1/VIN2, VIN3/VIN4, VIN5/VIN6 and VIN7/VIN8—see Table II.
CH2, CH1, CH0 These bits are used in conjunction with VIN8/AGND and DIF/SGL to select an analog input channel. Table II
shows how the various channel selections are made.
CONVST
Setting this bit to a logic one initiates a conversion. A conversion is initiated 400 ns after a write to the control
register has taken place. This allows a signal to be acquired even if the channel is changed and a conversion initi-
ated in the same write operation. The bit is reset after the end of a conversion.
EXTREF
This bit must be set to a logic one if the user wishes to use an external reference or use VDD as the reference.
When the external reference is selected the on-chip reference circuitry powers down and the current consumption
is reduced by about 1 mA.
C
相關PDF資料 |
PDF描述 |
|---|---|
| AD7813YRU | IC ADC 10BIT PARALLEL 16-TSSOP |
| AD7819YRZ-REEL7 | IC ADC 8BIT SAMPLING PAR 16SOIC |
| AD7820KP | IC ADC 8BIT HS TRACK/HOLD 20PLCC |
| AD7822BRUZ-REEL | IC ADC 8BIT 1CHAN 2MSPS 20TSSOP |
| AD7823YRZ-REEL | IC ADC 8BIT SRL 2.7-5.5V 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7812 | 制造商:AD 制造商全稱:Analog Devices 功能描述:+2.7 V to +5.5 V, 350 kSPS, 10-Bit 4-/8-Channel Sampling ADCs |
| AD7812WYRUZ | 功能描述:IC ADC 10BIT 8-CHAN SRL 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7812WYRUZ-RL | 制造商:Analog Devices 功能描述:8 CH. 10-BIT Aanalog-Digital Converter |
| AD7812YN | 制造商:Analog Devices 功能描述:ADC Single SAR 350ksps 10-bit Serial 20-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:8 CH. 10-BIT ADC I.C. - Bulk 制造商:Analog Devices 功能描述:IC 10BIT ADC 8CH 7812 DIP20 |
| AD7812YNZ | 功能描述:IC ADC 10BIT 8CHAN SRL 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。