- 您現在的位置：買賣IC網 > PDF目錄10684 > AD7789BRMZ (Analog Devices Inc)IC ADC 24BIT LP 10-MSOP PDF資料下載
參數資料
| 型號： | AD7789BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/20頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT LP 10-MSOP |
| 標準包裝： | 50 |
| 位數： | 24 |
| 采樣率（每秒）： | 16.6 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 230µW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
AD7788/AD7789
Rev. B | Page 14 of 20
ADC CIRCUIT INFORMATION
The AD7788/AD7789 are low power ADCs that incorporate a
Σ-Δ modulator and on-chip digital filtering intended for the
measurement of wide dynamic range, low frequency signals,
such as those in pressure transducers, weigh scales, and temper-
ature measurement applications. The part has one unbuffered
differential input. The device requires an external reference
voltage between 0.1 V and VDD. Figure 10 shows the basic
connections required to operate the part.
03
53
9-
0
6
IN+
10F
0.1F
IN–
OUT–
POWER
SUPPLY
OUT+
REFIN(+)
CS
DOUT/RDY
SCLK
VDD
GND
AIN(+)
AIN(–)
REFIN(–)
AD7788/
AD7789
MICROCONTROLLER
Figure 10. Basic Connection Diagram
The output rate of the AD7788/AD7789 (fADC) is 16.6 Hz with
the settling time equal to 2 × tADC (120.4 ms). Normal-mode
rejection is the major function of the digital filter. Simultaneous
50 Hz and 60 Hz rejection is optimized as notches are placed at
both 50 Hz and 60 Hz with this update rate (see Figure 6).
NOISE PERFORMANCE
Typically, the devices have an rms noise of 1.5 μV rms that
corresponds to a peak-to-peak resolution of 16 bits for the
AD7788 and 19 bits (equivalent to an effective resolution of
21.5 bits) for the AD7789. These numbers are for the bipolar
input range with a reference of 2.5 V. The noise was measured
with a differential input voltage of 0 V. The peak-to-peak
resolution figures represent the resolution for which there is no
code flicker within a six-sigma limit. The output noise comes
from two sources. The first is the electrical noise in the semi-
conductor devices (device noise) used in the implementation of
the modulator. The second is quantization noise, added when
the analog input is converted into the digital domain.
DIGITAL INTERFACE
As previously outlined, the AD7788/AD7789 programmable
functions are controlled using a set of on-chip registers. Data is
written to these registers via the serial interface and read access
to the on-chip registers is also provided by this interface. All
communications with the devices must start with a write to the
communications register. After power-on or reset, the devices
expect a write to the communications register. The data written
to this register determines whether the next operation is a read
operation or a write operation, and also determines to which
register this read or write operation occurs. Therefore, write
access to any of the other registers on the devices begins with a
write operation to the communications register followed by a
write to the selected register. A read operation from any other
register (except when continuous read mode is selected) starts
with a write to the communications register followed by a read
operation from the selected register.
The AD7788/AD7789 serial interface consists of four signals:
CS, DIN, SCLK, and DOUT/RDY. The DIN line is used to
transfer data into the on-chip registers and DOUT/RDY is used
for accessing data from the on-chip registers. SCLK is the serial
clock input for the device, and all data transfers (either on DIN
or DOUT/RDY ) occur with respect to the SCLK signal. The
DOUT/ RDY pin operates as a data ready signal also, the line
goes low when a new data-word is available in the output
register. It is reset high when a read operation from the data
register is complete. It also goes high prior to the data register
update to indicate when not to read from the device; this
ensures that a data read is not attempted while the register is
being updated. CS is used to select a device. It can be used to
decode the AD7788/AD7789 in systems where several compo-
nents are connected to the serial bus.
the AD7788/AD7789 with CS being used to decode the devices.
Figure 3 shows the timing for a read operation from the output
shift register, while Figure 4 shows the timing for a write opera-
tion to the input shift register. In all modes except continuous
read mode, it is possible to read the same word from the data
register several times even though the DOUT/RDY line returns
high after the first read operation. However, care must be taken
to ensure that the read operations have been completed before
the next output update occurs. In continuous read mode, the
data register can be read only once.
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY lines are used to
communicate with the AD7788/AD7789. The end of conversion
can be monitored using the RDY bit in the status register. This
scheme is suitable for interfacing to microcontrollers. If CS is
required as a decoding signal, it can be generated from a port
pin. For microcontroller interfaces, it is recommended that
SCLK idles high between data transfers.
The AD7788/AD7789 can operate with CS being used as a
frame synchronization signal. This scheme is useful for DSP
interfaces. In this case, the first bit (MSB) is effectively clocked
out by CS, because CS normally occurs after the falling edge of
SCLK in DSPs. The SCLK can continue to run between data
transfers, provided the timing numbers are obeyed.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1720CS8#TR | IC COMP DUAL R-R 4MA 4.5NS 8SOIC |
| LTC1445IS#TRPBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| CS5530-ISZ | IC ADC 24BIT 1CH W/LNA 20SSOP |
| LTC1443IS#TRPBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| XRD8785AID-F | IC ADC 8BIT PAR 15MSPS 24SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7789BRMZ-REEL | 功能描述:IC ADC 24BIT SIGMA-DELTA 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD779 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit 128 kSPS Complete Sampling ADC |
| AD7790 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16-Bit Buffered Sigma-Delta ADC |
| AD779-05A6 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AD7790B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, 16-Bit Buffered Sigma-Delta ADC |
發布緊急采購，3分鐘左右您將得到回復。